Portable Repair Stand V3 | Made in the USA | 3.7" Ground Offset, for Bicycles, eBikes | Compatible w All Electric Bikes

Haven't had to use these yet but know I will someday. The quality is very good and they pack up small in my bike bag. I have put them on, just follow the instructions and you'll be good👍

I wasn't sure about this purchase but I'm so glad it did, though they were a little costly, but now I know there worth every cent! I can now work on my E-Bike upside down with out worry and protects all the stuff on my handlebars!

A little expensive, but seemingly well constructed. Probably partially so expensive due to the niche nature of the product as the manufacturer likely doesnt produce these in giant batches.They put magnets in the sides of the legs so that when you mate them by intersecting the legs of each one together the magnets hold them in place.The length of each holder is actually half the length listed in the product dimensions table, so the info listed in the manufacturer’s info graphics is correct.Ive used them a few times now and they worked great to prevent my light mount/brakes/shifters from getting marred.Just be careful when placing the bike upside down that you are gentle as you could potentially snap a leg if you put the bike down forcefully.I recommend using with a brake bleed block if you need to take your wheel off and have hydraulic brakes, so that the brake pistons dont close up and make the pads hug the rotor once you put the wheel back on.Once the wheel is back on, you can also recenter the pistons by loosening the bolts used to mount the caliper and then fully squeeze the brake lever and tighten the bolts while still squeezing the brake lever. The lever should make the calipers center around the rotor so it doesnt rub on one side.

I have an e-bike and I needed to fix a punctured tire. Flipping the bike upside down to repair it could've broken the dashboard. These handlebar jacks easily attach to the handlebar grips and provide adequate distance to protect the dashboard. They fold compactly and are magnetic so the attach to each other , they fit nicely in my tool bag.

I have a 50 lb. e-bike which requires me to oil the chain assembly from time to time but there's no one to hold the bike up and I didn't want to buy a bike maintenance stand. These Handlebar Jacks worked perfectly...easy to use, perfect off-the-ground (garage floor) height and I like how they are held magnetically together for storage!!Thank you!

Works as they should. I like that they are compact and easy to store in a drawer, unlike a bike stand.

Very useful.

I was using these jackstands on the handlebars of a heavy ebike with a rear rack frame protected with a mover's blanket. While servicing my brakes, the jackstands rolled with the curvature of the tube of the handlebars and the jacks tipped over to their sides. So I decided to tighten the straps while placing them back upright. However there seems to have been a small tear on one of the straps due to the stitching and it tore theough the strap while trying to fasten them back on.The velcro for these straps are made with velcro hook on each end and there are no suitable replacements I could find on Amazon, no way of getting replacements, or alternative ready-made solution. These straps are 3/4ths of an inch and still looking for an alternative solution.Secondly, the tripod angle on these are not wide enough to account for rolling on thebhandlebars. The idea is good but the design could use improvements:1. have a much wider base to prevent any tipping over, especially with heavy ebikes with a display screen.2. have a robust and stronger strap that cannot be preforated by the zigzag stitching.

A must have to support your handle bars off the ground used on electric bike kept everything off the ground very stable

A composite jack great for roadside repair. My E-bike weighs 35kg & these jacks hold the bike well, functional & don't take up much room in the pannier bag

At first, I thought that these were just a gimmick. I decided to purchase them and try them out. Man,I was surprised! They are super easy and handy to use. When you are on a trail and need to do a repair, it is super easy to put on, flip over my bike and fix my flat or whatever. It was such a pain to fix a flat when you are on a trail and you have no way to keep the bike stable. These solve that problem. I highly recommend these.

I carry the Original Handlebar Jack V3 with other emergency gear in a handlebar bag (e.g. to make it easier to remove a wheel) and they are also useful for some simpler maintenance and cleaning tasks. Usage is simple: pull the two jacks apart (they are held together with a magnet), open the tripod legs, strap (upside down) to suitable points on handlebars, turn the bicycle over until the jacks and seat are on the ground. The jacks are best suited for working on the bike on reasonably level ground, but - with care - stable if the ground is not perfectly level. When work is done, turn the bicycle upright, undo the straps, close the tripod legs, and put the two halves together.

Worked great and boy did these jacks come in handy. I’m so glad I decided to have these in hand in my bike kit.