Cramer Fugi 5 Kit Grouting & Silicone Profiling & Applicator Tool Kit

Works well with a great finish but have a little practice

Amazing kit. Makes the job so simple and looks professional. Highly recommended 10/10

Good if your walls are perfectly square or perpendicular, but a pain if they are slightly off, which is the issue I had. The angle between 2 of the walls in my shower was slightly less than 90 degrees, which meant these tools were not quite what I needed. For the corners that are 90 degrees, they are great, but I had to use another silicone tool that worked better in awkward spaces for some of my joins. Would have given 5 stars if there was a tool included that worked better for awkward spaces. All that said, I am still keeping them for future silicone jobs!

I got put onto this product by my brother and I'm very happy I gave it a go. There are a few good YouTube videos but I'm not sure if I can put the link in. Essentially put all the tools up to the area you want to seal and find the size you want, then cut your nozzle FLAT and NOT angled and cut it to the width of the tool you are using, eg 10mm chamfer, cut it to 10mm width by overlaying the tool on the nozzle. Force the sealant into the joint at right angles moving slowly and the bead will be the correct size for the tool. There are a few things that you must do to get a good finish. If doing a shower do the corner uprights first and leave to bond for 24 hrs before doing the bottom corners otherwise you will end up pulling the upright corner sealant with the tool. If just doing round a sink do the two opposite sides and leave to bond for 24 hrs and then do the center section for the same reason. At no point you should use a soap solution, the tool has release agents impregnated in the rubber and glides effortlessly over the sealant and you wipe the excess off as you go. Using soapy solution hampers adhesion to walls if there is any slight gaps and it goes down including it changes how the sealant is removed using the tool and gives a poor finish. These tools give a consistently excellent professional finish and I highly recommend.

Got this to do my first silicon job in the house. Never used it before. First off there is feet to allow it to skip over grout so the bead is level. This caused more issues than helped but that might be me. They do help but I think because they are plastic they have a different friction. Also the feet make it hard to hold and position.What to be aware of is the amount of pressure used. Not to much not to little. It's almost a confidence thing. For my job each bead got better. Looking at the rest of the bathroom this tool made my beads look way better than any other in the bathroom.Turned what could have been a nightmare into a tidy job.Just need a tool to help me with the silicon gun and Ill be ready to tackle any job

I held back on buying the kit as i simply couldn't justify spending that amount on a set of plastic assortments for very occasional use.HOWEVER, That said!! This has been one of my best buys so far this year.This makes profiling much easier and produces a nice, professional finish with lots of varying options.The finish is so good and consistent that it beats any sealant finish ive seen done using the "finger method" which also introduces bacteria and compromises the mould protection of your silicone.I particularly liked the little black guides for use on rough/uneven surfaces, also the plastic case is smart and of a sensible design.My kit did not come with instructions but i was able to figure it out with no stress.If you are a pro or keen DIYer just get the kit. Its sturdy and of good quality which should last for many years.An added bonus is that the silicone wipes cleanly off the attachments but you may have to use a tiny pointed screwdriver to remove excess silicon from the crevices.Only snag is that you may use more silicon than the "finger" method so do bear that in mind and get a big paper roll or paper towel to handDefinitely worth your money!!

Well deserved reputation for applying silicon or caulk.Initially thought the kit was overkill but the removal tools are really helpful. It's essential to remove all the old silicone else the mould will come straight back.

The set has a good variety of profiles including the sizes I use most often. The kit was a bit pricey compared to other brands. Happy with the even smooth surface of the silicone. Longevity to be seen.