Vantec CB-ISATAU2 SATA/IDE to USB 2.0 Adapter Supports 2.5-Inch, 3.5-Inch, 5.25-Inch Hard Disk Drives (Black)

Adquirí este producto realmente me ha funcionado muy bien sobre todo para realizar respaldos en discos duros IDE, llego antes de la fecha esperada, los materiales son de buena calidad, lo recomiendo.

I bought this product because I was not prepared to put out 100.00 to have a computer shop do it for me.I am not a real computer savvy person and I felt that it was cool to have some thing more than my hard drive info after all was done. Got what I was after plus some pictures I had forgot about.This product worked fine for me.I had a 2.5 inch IDE hard drive from a old Dell laptop that packed it in and I did not relize that there was a adapter over the pin bar on the hard drive.A fellow at Staples set me straight on it and all was good..Just pulled it off.And it fit right into the reader..Cheers

I bought this to use on my 3.5" drive, but I wasnt able to use it. One - the power output was too high for my 2TB WD Caviar Green drive and so smoke started appearing from the HDD while using it. I dont know if I damaged by HDD yet, but the lack of power control is a serious issue with this. MOdern HDD's are quite efficient, so utility of this is questionable without power control. The cables are also delicate to touch and need to be handled very carefully. Overall, not an easy experience and not what was expected.

I just tested my new Vantec CB-ISATAU2 today. I have seen everything from very positive to very negative reviews on this product, but my experience so far is quite good, though I have only owned the product for one day. So I would recommend this product based on my initial experience, but I cannot vouch for its longevity. I conducted my tests using Windows XP Pro 32-bit on a Dell Inspiron E1505 laptop with USB 2.0 ports. (I did not test the transfer speed as this is very much dependent upon the particular source and destination drives used and the nature of the data transferred (sequential or random). I don't feel like doing a proper speed test.) Here are the results: 3.5" IDE Hard Drive Test ------------------------ This is an old IBM Deskstar from 2001. The connection to the IDE port and to the power were both solid and the connections were easy to make and held firmly. I initially used the Cable Select jumper configuration because that is what was already set and this worked fine. I then tried Master and Slave and both of those worked equally well. I have read in at least one review that it may be important to turn on the power to the drive before connecting the USB to the computer, but connecting the USB before the power worked just as well for me. However, disconnecting the power before the USB resulted in the operating system not recognizing that the device was no longer present, until I disconnected the USB. No problems resulted. In neither case did I bother to "Safely remove hardware". Sometimes when I connected the drive Windows gave me a "USB device not recognized" followed by a "This device can perform faster" notice. I did not determine what caused this, but the drive was still accessible in both cases. Sometimes there was a fairly long (I counted 32 secs. once) delay between the time I connected the USB and when Windows began scanning the drive and mounting it, particularly after receiving the above mentioned notices. This delay seemed to happen most consistently and for the longest time if I plugged in the USB and then unplugged it without ever powering on the drive, then powered on the drive and plugged the USB in again. Windows always recognized the drive eventually. So be patient before deciding that the device isn't working. 2.5" SATA Hard Drive Test ------------------------- This is a Hitachi drive from 2008. My experience with this drive was the same as with the other, excluding the jumper configuration tests which do not apply, and the delay problem which did not seem as bad. Everything connected well and the drive was recognized and worked properly, regardless of which order I connected the power and USB. Again, I did not "Safely remove hardware" first and no problems resulted that I am aware of. General Assessment ------------------ As I stated before, all connections were easy to make and held firmly. Just as in the case of internal molex power connections, this one, too, is very tight. The power switch on the cord works perfectly and seems to be of decent (not excellent) build quality. The build quality in general seems decent as well. The power block has what I consider to be a reasonable weight for such low wattage (12.0V @ 2000mA and 5.0V @ 2000mA). Nothing rattles and everything seems reasonably durable. The only minor exception is the molex to SATA adapter which appears cheaply constructed. But it worked, and it can be cheaply replaced if necessary. The power switch block on the cord has a small, green LED on it which indicates the status of the switch. The data adapter has a red LED which lights up when the USB is connected, and flickers between bright and dim to indicate activity.

Had to pick this unit up to transfer some old hard drive data to newer, modern drives. Even helped some people out in recovering data from laptop drives, where the drive was fine, but the laptops suffered various board/power failures. As others have mentioned, this thing works in a pinch. Does what it's meant to do, no fuss, no fluff. Did not experience issues with drive detection or interruptions in transfers. The whole power brick is a bit inconvenient, but it's nothing to raise a real complaint about. I didn't expect a fantastic price, but it was fair considering I had no headaches using the unit.