Hallmark Industries MA0419X-12A, Deep Well Submersible Pump, 2HP, 230V 60HZ, 33 Gpm, Stainless Steel, for 4" or bigger well

Pump has been running perfectly for over 2 years. Feeding 3 houses, 260 feet deep, with NO check valve at the pump (just one at the top).The construction is excellent. After reading some negative reviews when I purchased it, I invested in some additional quality electrical supplies and took my time to make sure every connection was solid and absolutely sealed. I suspected it at the time, but after two years with zero issues I'm convinced the number one issue with this pump is people misunderstanding and/or doing a poor job with the wiring. Take your time! Be absolutely sure every connection is rock solid, sealed with adhesive lined shrink tubing, and then use PVC pipe wrap tape to secure all your wiring to the bottom of your piping so they won't wiggle and risk coming loose. And use a check valve at the pump. I didn't because I couldn't get one in time and needed water, but you should.I tested mine every step of the way. First in a garbage can just overflowing the water on top of itself (with the wiring covered). Then with the piping attached, emptying back into the garbage can (I did this to clean out the pipe a bit too, but that was unique to my situation). Then again about 20 feet into water in the well. Then of course again at the bottom.I will 100% buy again. At this price I may just keep one on hand.

Installed july 2023. Added check valve to pump and drilled 1/8" bleed hole per directions. Installed down to 226 ft with torque arrestor on 1 1/4" line. Got 24 gallons per minute flow at well head. installed Barrett Pump Stop 1" Plastic Valve - 50# just before the check valve going into the pressure tank to control pump stopping too quickly. So far working great! I get all the water I need. My well produces prodigious amounts of water. I plan to tee off the tank line to feed irrigation on the land next spring.I'll check back in the future to add any comments on performance issues I encounter. 1/25/2025

Used this to replace a dead red jacket 1.5hp pump for my irrigation system. Its about 4-6 inches longer, but seems to be a perfect match and drives my sprinkler heads the same as the old one. It came with wire crimps and submersible adhesive grade heat shrink tubing. I made the mistake of attaching my wires before putting them through my well casing in my pvc riser which sits on the bottom (doh!)... but, no worries, you can buy another well grade heat shrink tubing kit from Lowes. I like the tubing from Lowes a bit better as the tubing is Longer and looks more like the black tubing that was used to seal the old motor connection. That said, I'm sure the clear tubing they provide will work fine provided you follow instructions and make sure you take time with your heat gun and make sure you see the adhesive start to bleed out around both ends. So far, I'm very happy with this purchase! It came well protected during shipping and was easy to assemble. The hardest part is reattaching the metal intake screen once you connect the motor/impeller units (very tight, but have patience and you will get there!). The old red jacket pump lasted nearly 15 years-- would be cool if I get this kind of life out of this one, but time will tell right?

I have bought 3 of these. 1 died after a week, 1 lasted 1.5 years and died and the 3rd i put in less than 2 weeks ago and it died already. Its residencial use for irragation so not uaed alot.these are junk. Its not easy to pull up a pump thats 120 feet below ground. Save yourself the aggrevation and buy a good pump.

Bought this because my well pump quit on me. This one has been in for 2 months so far no problems.

Easy to connect ... just follow instructions ... I did a full replacement on my well (approx. 250ft deep) ... new pipe, check valve, all new fittings ... Not to mention went with new wiring as well. For the cost saved me $$$$ doing it myself than have a pump company fix it. Easy to do .. check out YouTube on some installations of sub pumps. Built special tool to fit on my well head to roll the pipe into place. EASY! .. My well pump now gets the water up the lines in a hurry .. and pressurizes quickly compared to my old worn out pump.

Awesome pump great price

The pump appeared to be well made. Installation was easy. I was happy with the rope attachment size even though some were not. I bought this some time ago and just got around to installing it. It performs as advertised and very accurate to the charts provided for flow. I have not had time to gauge the longevity, but I see no reason for that to be a problem as its working great. I am very happy with a pump without a control box. When ordering your pump pay close attention to the chart for pump sizing mine was right on the edge between one and two horsepower and I think I bought one a bit too large. My bad not theirs. Their customer support was immediate with a couple of questions I had.