Prazi 12" Beam Cutter Attachment for Worm Drive Circular Saws – Model PR7000 for 7-1/4"-8-1/2" Worm Drive Saws – American Owned Company – Increase Cut Depth from 2-1/2” to 12”

It was a easy install on the saw and it worked fantastic. I would recommend this product to everyone

I purchased the Prazi 7000 to go on a Skil 81/4" saw. It took me about 30 min to set the Prazi on the Skilsaw, being you have to take the blade guard off of the Skill worm drive saw. I have a large timber beam project I took on at my home and have to make approximately 200 crosscuts, miter cuts and lap joints on 6 X 10, 6 X 8, 6 x6 and 4x6 cypress beams. I had a few questions when thinking about purchasing this tool rather than using my 16" beam saw. I called Bob on 3 separate occasions, and he was quick to answer the phone and give me the guidance on what I needed and any assembly questions.After assembly and alignment of the saw I crosscut a 6"x10" beam and it was like butter to cut, and the face was flat and straight even with no guide! I have to make over 25 lap joints on my 4" x 6" purlins. I made another lap joint test cut on a 4 x 6, again by free hand and it wasn't perfect but with a guide it would have been, and it only took less than a minute. If the rest of my project goes as good as the test cuts, this tool will save me hours upon hours of time.I'm giving this tool 5 stars because of price point, ease of assembly and use and something else that is hard to find these days is great customer service. Thanks Bob!!1

This beam cutter is awesome and works great! I checked some cuts against my miter saw to make sure they were straight and they were right on!

So I didn’t give a full 5 stars for these reasons:REGARDING 12” model: on a 12x12 beamThe chain & base are rather thin & in order to get precise cuts with no fraying/splinteringthe chain needs sharpening quite often. A simple chainsaw sharpener will work great (kits come with 3 files & a base to hold chain in place. Takes some time, but you can get it much sharper than how it comes from seller)Install was a little finicky on one of my Skilsaws, didn’t work on my Makita, but finally worked on my 2nd Skilsaw.Overall it’s a pretty decent tool, it’s much cheaper than buying/renting a beam cutting saw (16” Makita) and saves me the trouble of doing cuts on various faces of a large piece of wood.That being said, I’m using this Prazi blade as a means of cutting 1” thick pieces of end grain off of a 12x12 beam. It’s doing the job but it requires a lot of maintenance to rip through a heavy piece of lumber like this.If you’re a hobbyist or doing 1 or 2 jobs this is a great and relatively inexpensive tool to have (beam saws go up to the $700-800 range for large quality tools and generally cut up to 6 3/4 inches).I still have about 44” of wood to cut with this little Prazi attachment, I hope it can do the job.ONE THING TO NOTE!!!Being that my project is a heavy piece of lumber, I may be pushing this Prazi blade too much. One of the photos I attached shows one of the bolts that holds the chain base to the worm drive fitting (which in turn attaches to your circular saw). It broke on Friday afternoon & I was forced to replace it with a machine screw from the local steel shop. Ive also attached a photo showing that the threads are starting to strip on the attachment itself.All in all, pretty good product, just be aware that not every circular saw is the same so do your research before you order. Also, if you are trying to cut thicker pieces than 12” I would suggest going with the 18” model made by Prazi.If Prazi products don’t work for you, there’s a lot of information out there on rigging a chainsaw to a jig made of 2x4s to get precise and level(ish) cuts.Work safely

Prazi PR 7000 Beam Cutter Awesome addition to the tool collection…nice square cuts… relatively easy to get set up. The saw I set up will remain the beam cutter saw permanently!!!!Great customer support…5 star all the way….

Just no.Cuts great first cut unfortunately every single bolt and screw will rattle out guess they don’t believe in locktite. After 2nd cut chain was loose went to tighten and snapped tensioning bolt off. Turns out the chain tension bolt’s threads are machined into soft aluminum and will strip out when you go to tighten it with minimal force. That was after the screws for riving knife rattled out and chain cut into it . They charge twice as much to build it in the USA then use the same cheap parts as the harbor freight model . Sent pictures of bolt stripped out they offered to replace if I paid for it. Sorry just gonna return

I have a new saw I went and bought and a two year old DeWalt, didn't fit either one. Went and dug out a very old Ryobi I've had forever with a bigger bolt than supplied and it fit perfectly once I found a bolt that would fit out of my bolt bin. Cuts good but if your a novice user, make yourself a straight edge to get rid of the wavyness. It's also hard to see a line due to the chips that it throws up and guess that's to be expected. Other than that, it's a great tool to have, was surprised to see a chain adjustment because some of the others don't have one. just hope it lasts!

Well built and easy to install? Works well with my gear drive Skil Saw. Would buy agsin