JonsboN4 Black NAS Pc Case, Walnut Wood, 8-Drive Bay/6 * 3.5 "HDD (4 hot-swap,2 Non hot-swap),2 * 2.5SSD,Micro ATX Chassis, USB3.2Gen2Type-C, 1x120mm Fan Built-in, Black

This is one of the nicest cases I've ever used for a system build. Well designed with nice features, making it easy to access. Plenty of room for motherboard and CPU cooling fan. Cable routing a breeze. The case fan is a bit noisy, but I used a fan controller to slow it down to a reasonable speed to minimize noise. Big enough to get the job done, yet compact enough to fit on a book shelf. The walnut panel adds a bit of class!

Unsurprising to anyone this case is somewhat cramped to work in. Anyone with any system build experience could have called that. What couldnt have been called however was how obnoxiously bad the included fan is. When i tried running the NAS i built in it over night all i could hear was this low pulse constantly through the night. Eventually i turned it off from my phone and ordered a noctua fan for it. Upon inspecting this bundled no-name fan i noticed it had a very pronounced wobble which was likely the culprate of the awful noise. After a fan change and opting to use the 4-pin fan header on the motherboard instead of the 3-pin header on the daughterboard the acustics arent bad (and the cooling is ever so slightly better)Another issue that is minor for me but could be major for someone else: be sure to observe the length of the motherboard power connector on your PSU. You want something thats over long so you can route it off to the side and back around instead of straight through the front side as doing this will make the top 2 drive bays un-usable. Not a deal breaker for me but if you had planned on using all avalible bays this could be an issue for you. This probably goes without saying but i highly recomend a modual PSU to pair with this case because, as stated previously its very cramped and while you have basically 360 access to the top chamber you dont have the same ease of access to the bottom chamber.If you are planning on using this case for a system that does more demanding tasks than acting as a home storage or media server i would probably look elsewhere as there is only 1 120mm fan mount and there isnt a lot of room for a GPU or a good cooler for a modern high end CPU. Still for a NAS for a home lab or media server it's beautiful and functional.Ps: also be aware that there is a green indicator light on the daughter board that is very apparent in the dark. I mention this because i was unaware of it until i had gotten it up and running and i couldnt find infor about this anywhere prior.

My unit had a DOA fan near the HDDs. I had to buy another ($10).It doesn't have walnut veneer as advertised.The case is laid out in such a way that the 24 pin ATX power connector couldn't reach. I had to buy an extender ($15)There is not any cable management help. There are not places to loose tie cables. There are only two holes in the plate between the top and bottom of the case and they are both on the sides near the back. The holes didn't have grommets and were rough enough to take some of the coating off my cables.The HDD cages don't use a sled system. Instead, it requires you to put 6 screws and grommets together on each HDD. It works but is as easy as other systems.Overall there were a lot of little problems and inconveniences I felt I shouldn't have had with a case charging this much.

I'm loving the case. It's very sturdy, the wood front is very sleek and modern and overall just very easy to work in. I'm using it for my Plex server that has a 10400, 32gb ddr4 ram, 2x 4tb HDD's, 2x 1tb HDD's and a 500gb Samsung 970 for boot drive.Case actually is SMALLER then it looks in the pictures, which was a good thing for me since I love smaller builds. Plenty of room inside especially if you go with a mini itx board which I did. Cables were very easy to route in this case with no issues finding a path for them to the motherboard.

This case is an exceptional value, If your looking for a small form factor Nas case this is absolutely perfect. The build quality and materials are high quality. Building in this case is tight but doable. Cable routing for the 8pin CPU isn't great but no one will see that. There is a spot on the MB tray that can be cut out to run the 8pin CPU cable through, I didn't because it's not that big of a deal to me. There is no reset button on the front of the case. The front panel connector is a solid connector not individual connectors. This case is an item that I can highly recommend.