xTool Selected Acrylic Sheet Trial Kit, 10-Piece 12" x 12" Plastic Plexiglass Sheets 1/8 Inch Thick Orange, Black, Green Glitter, Yellow, Red Opaque Acrylic for Sawing, Laser Cutting & Engraving

If you intend to shine light through these:- they are mostly opaque, so you won't really seen through them- absorption, they absorb light, basically they illuminate evenly, but will absorb a lot of the light. So they probably make a nice sign, but if you want it to double as a source of light to illuminate other things, like in photography, it will take a big amount of light down. soft, but low.Conclusion:- I cannot speak to the laser etching or signage aspects, but the product arrived in pristine shape. Seems mostly opaque, and useful at spreading out backlighting while still illuminating.- in photography, this one is a mixed bag, and I feel you may want more transparency to pass diffused light more efficiently, and as an under lit table top, it is either the best of both worlds or not opaque enough? The color is also mostly pure white, and it seems to work well enough. I felt it has like a 1% warming effect. most people won't notice. it is better than a lot of "white" plastics, but is not perfect. good enough though.Thickness? idk what I was expecting, but i guess because i wanted more light to pass through, and this was a bit more opaque than I wanted it to be, I guess it looked thick, but it certainly helped when used as a small table top for small products.

This is listed as 12" while it's just a hair over 11.75" (almost a 1/4" short) on both directions. Also listed as 1/8" (3.17mm) but is really 2.86mm (quite a bit off).Basically a bit smaller than they say but the quality seems to be good. I purchased red and blue and while the red is dead on color wise the blue is just a little towards purple, can still be called blue I guess but not exactly the color shown on screen.Came packaged nice, came in a padded bag that wa then in a box and then Amazon but that into another bag. Arrived damage free.Would I buy again? Yea probably unless I found a better product.

Updated: The seller issued a refund for the problem acrylic. Happy with the customer service, not so much with the acrylic itself.Previous review below:I ordered the grass green acrylic sheets because the listing specifically said it was cuttable with the xTool D1 Pro diode laser. I even got a detailed list of machine settings with the acrylic straight from xTool. Here's the rub - this color really isn't at all cuttable with a diode laser, not with the recommended settings nor with just about any other adjustment I could think of. It simply won't cut all the way through.There is nothing wrong with my machine, it cuts many other acrylics beautifully. I fully realize that there are some colors of acrylic I cannot cut with a diode laser so sometimes it's really just a best guess as to what will work, but when the listing says that it is cuttable and is applicable to my specific machine I expect to be able to cut the material I've bought. Not happy.

It's good with my 20 W diode laser.

I purchased this to try to make earrings with on my laser engraver. I tested out the material on both a 10watt diode laser and a 45watt CO2 laser. The 10watt did an OK job. A little rough around the edges but i think it is due to the laser limitations. I made the same item using a CO2 laser and it cut like butter. So smooth and crisp.Overall, the material was packaged REALLY well and had zero flaws. I will definitely be buying this again in the future.

Arrived quickly, packaged expertly. I needed some last minute acrylic to make signs with my Glowforge, and these fit the bill perfectly. My machine and I were very happy!

I got these for a logo project I'm making with the laser. The scattering on this is such that it is very difficult to cut with a 20 watt 455 nm diode laser. It engraves nicely and will cut smaller pieces, but for large pieces (I was doing about 6 x 6 inch parts), the kerf cools down and the material re-flows during a pass so you never get a through cut, no matter how many passes you attempt (I stopped at 11). Because of the scattering with this color, fine details are lost as well because the scattering heats and removes material beyond the normal laser kerf. Update: I will give credit to the company. I was contacted and offered a refund for this product. I really appreciate that kind of customer service.

The media could not be loaded.  Tiene buen espesor para lo que utilizaré, aplicar sellos de silicona. El corte se ve muy bien. El plástico cubre bien la superficie, parece que fuera opaco pero cuando lo retiras se ve transparente.