Replacement Vacuum FAN Impeller Kit For Kirby G3 G4 G5 G6 G7 G7D Sentria I & II PART # 119096S

Worked for my G-10D Kirby. After 12 years and shag carpet, its like brand new again with the new part. Its been a few weeks since the replacement and have had no issues. Be aware, the inpeller fits very, very, very, snuggly. It took longer to get the impeller fan on than it took to disassemble/reassemble the vacuum. A propane torch to heat the old one for removal. Wd40 to help get the new one on. And RTV silicone for the new gasket.

I was repairing the fan assembly on my Kirby G4D. The part is listed as fitting the Kirby older Generation models. IT DOES NOT! The hole is too narrow to fit the shaft of the Generation models. I took it to a Kirby repair shop. The owner said it is not an OEM product endorsed by Kirby. It was yellowish in color and the logo was wrong. He stated they would be white even a little greyish but not yellow. He sold me the correct part for $22. He did not reccomend drilling the hole larger since this would compromise the parts strength and it would break within a couple weeks. Also the machine would possibly be loud and it could damage the machine. My older fan part was firmly on and it took WD40 and the help of a second set of hands to wiggle and pull it loose. Do not try prying under the blade. As another reviewer stated, It will damage the shaft. I replaced the fan blade on another Kirby and I had to remove the handle assembly (which is held on by 2 screws on top) to reach the motor shaft with a 9mm wrench to keep it from turning while I unscrewed the old end piece. Hope this helps it was a very easy repair. Remember to purchase a tube of selant.

Fit my g4 perfect! Its like a brand new vacuum! I dont know why everyone is saying theirs dont fit. When you take the old fan off make sure you keep the washers in order so you know what order the new ones go on in, because it comes with extras. Also when you put the new fan on make sure you beat it on. That is what holds the fan on tight so it doesn't slip. Im so glad to have my vacuum back in working order!

Good Quality-should contain washer placement diagram

I needed a fan for one of my Kirby's since the original was totally wore out and out of balance. The kit arrived quickly as expected. Took a bit of beating to get the new fan blade on. I tried using the included 'nut/belt drive' but the bore was too small and just would not go on the shaft. My old one was ok so just reused it and now my old Kirby is one sucking machine again!

Do not buy! This product is advertised as fitting G4 modelKirby vacuum cleaners, and it does not. The fan cannot be mounted to the shaft without potentially damaging it or the vacuum itself. The spindle is also incorrect, and does not thread onto the G4. WARNING: Attempting to install this spindle onto your vaccum cleaner will result in permanent damage to the threads on your Kirby G4. If such damage occurs, you will be required to replace the shaft which requires a complete disassembly of the motor, or a replacement motor. This product is not compatible with G4 Kirby vacuum cleaners, and since it advertises itself as such, It seems like kind of a scam too me. If you're G4 needs a new fan, save your time and money by looking elsewhere.

This fit my machine and was an easy project to replace the impeller that was damaged. I am an elderly female that does a lot of diy projects to save money. You tube helps but also ensure you have the correct parts numbers from Kirby manuals. This was exactly what I needed to make my Kirby work better and not sound like a jet engine. It was a lot cheaper to do it myself and the parts looked exactly like the original damaged parts. The repair has lasted over 6 months now.

Really small. It didn't fit

Passt und tut was es soll.👍

I had the impeller on mey kerby vacuum replaced, the belt pulley didn’t match the original one and after 2 months of the new impeller it shattered into pieces, don’t buy part from this seller unless you want your $3000 vacuum ruined

Schnell und unkompliziert, gern wieder

Staubsauger läuft wieder. Er wurde in einem Reparatur-Café repariert.

Einbau war etwas knifflig, aber der 30jahre alte Kirby ist gerettet.