VEVOR Diamond Core Drilling Machine, 4in Handheld Wet Concrete Core Drill Rig, 1100-2400RPM Two Speed & 1-1/4" Thread & 2 Bubble Levels, 3-4in Drilling Diameter for Concrete Brick Block Stone, 1500W

I bought this to drill a couple of holes through 8” cured concrete foundation walls. It’s inexpensive compared to pro brand equipment, but seems to be every bit as solid and tight. No wobble, no leaks. After coring two holes, anyway! The drill comes with a valve for shutting off the cooling water. It’s on a very short hose, with a nonstandard quick disconnect. I made up a short adapter that I just clamp on out of a piece of old garden hose - see the pictures. The 4” core bit included is really heavy and solid. I bought a 3” bit, not Vevor-branded, which was made of thinner material, but did the job. Wear your eye protection because it spits and sprays. It’s pretty loud, so I found it less fatiguing to use wearing hearing protectors. To drill, use the higher gear of the two-speed gearbox, if the saw doesn’t bog down, as you’ll cut faster. With larger cores, the motor won’t be able to maintain full RPM in high gear, which is critical for keeping the motor from overheating. The drill does best if you can push the bit into the concrete with a LOT of force. Larger models have drill press like levers that you attach to the concrete, but not the “small” version. I got tired pretty quickly holding it in position and pushing it against the concrete foundation, down in a skinny trench with my arms extended. And then…I hit rebar. It took a long time to grind through, and when I finally did, I could feel the difference. It cuts a lot smoother when in plain concrete. When I finally broke through, the far surface broke through a little before the edge of the bit was all the way to the other side, resulting in an opening that was slightly rough, not crisp. Not bad like an impact core drill would have done. It has a convenient bubble level for drilling vertical cores. I didn’t notice that it also has a horizontal level too, so I didn’t manage to get the hole perpendicular through the foundation wall. It was tilted by 3/8" across the 8” thickness of the wall. I had some trouble breaking the bit free from the threaded shaft because my 12” adjustable wrench didn't open far enough to fit on the hex flats. Fortunately I could hold it in my vise at an angle. It took a good yank on the wrench handle to begin to loosen it. If you’re handy, this drill and the appropriate size bit will cost far less than hiring someone to drill your concrete. And it’s kinda fun. If you don’t need it immediately, look for it on sale, as the price varies considerably over time.

Great little machine, and for only slightly more than it would cost to rent a comperable unit from an equipment rental company, I now own it. Not sure what I'll need it for in the future, but it very cleanly cut a 4" hole through my basement wall, and it made light work of it. Super powerful and easy to use. I spent more time stopping to check how deep I had made it because it was cutting so fast.

I purchased this because it was about the same price as a rental without all the hassle and then I would have the tool if I ever need to drill another hole. And it worked. Very well. But a few things you should watch out for if you are new to this work. First, a 4" dryer vent needs a 4.25 inch hole. Not a 4" hole. I suspect this is the perfect size for a metric country with metric ducts, but if you are looking to install a 4" dryer, the hole will be really tight and it will be hard to insert the exhaust cover let alone get the duct through the hole. The seller was absolutely clear on the hole size, but the customer (me) did not appreciate its significance and it is really hard to make a hole larger! The second issue is that the spring on the trigger is pretty strong. My foundation was 12.5 inches of poured concrete. It took quite some time to drill the hole (with breaks) and by the end my hand was cramping. Clearly more time in the gym and less writing Amazon review would probably help. One solution might be to have a lock, but with the potential for the bit to bind, this could be quite dangerous. I think a softer spring would be best solution. This brings me to the next concern. There does not appear to be a clutch on the drill. Twice the bit bound in the hole and it is quite powerful. My hole was 6 inches above ground so this was not a risk, but if I was on a ladder, it could have been quite scary. So definitely don't get the bit out of angle or you will quickly find the drill twisting out of your hand. Starting the hole can be tricky because the bit is water cooled and does not have a pilot drill to hold it in the center. To address this, I cut a 4" hole in a piece of scrap wood and rested the drill in the hole until it started to cut into the wall. This avoided the drill from wandering as it spun and before it started to cut. This take a bit longer but is worth the time! Speaking of water cooled, as some of the comments mention, the drill comes with a fitting that probably works great in China, but for which no US garden hose can attach to. I don't event know what it is. It looks a lot like the quick connects they have at HomeDepot, but it is a different size and does not stay connected. The fitting the male connector screws into is not tapered and is metric. So unless you have access to metric plumbing parts, you will need a 1/4 inch brass fitting and rely on it to cross thread (which it will with enough tape) and then a bushing and finally a garden hose connector to allow you to connect a US garden hose to the drill. The fitting is stainless steel so brass will deform nicely and work. Don’t use steel! This is a simple trip to Lowes or HomeDepot, but will set you back another $30. Last point is that this drill is heavy. If you are young and fit this may not be an issue. But it takes time to drill through any strong foundation and you will have to hold this drill quite steady for a long period of time or it could bind. So take lots of breaks, see if someone can spot you for a time or two so you don't make a mistake. I don't regret the drill, but do wish the 4 inch bit was a quarter inch larger. Given the hassle with getting the duct through the hole and converting it to work with our garden hoses, I would probably rent one next time since I only needed the one hole. But if you can work with a 4 inch hole or are using the smaller bits for irrigation hoses or wires (and they work with that diameter) and you will want to work over several days (like most DIYers), this is definitely worth getting because renting over multiple days is quite expensive. Hope this helps.

Slick! Works great, core drilled straight through rocks and concrete in an old foundation. The little hose they give you mounts right to the drill and add a def container , cut the bottom off and flip it over for water reservoir. I think it'll screw right onto a 2 l bottle also. It's the same price as a rental fee for my area.

Full disclosure- I have never used a core drill before. I needed to drill a 6” wide hole in a 10” thick concrete wall. All of the rentals (Home Depot, etc) were missing pieces of the mount/drill/you name it, and they were charging $200+ for a single day’s use. I found this drill and purchased a SALI 6” diamond tipped core bit. The instructions were somewhat lacking but eventually I got it all set up. I ditched the screws that “stabilize” the base and used 4x 1/4” diameter 4” long tapcon screws to anchor the base to my vertical wall. This thing is LOUD and honestly it kind of made me nervous. Use eye/ear/hand protection 100% of the time as well as a continuous(ish) stream of water to keep the tip wet/cool, it’s absolutely necessary. It took about an hour and a half to core through the 10” wall. Removing the concrete core piece from the core bit was INCREDIBLY difficult. I ended up having to buy a SDS plus chisel to completely fracture the piece of concrete for hole #2. Once I got the bit empty of the concrete plug I moved onto hole #2. This 2nd hole was unfortunately 9.5’ high and what turned out to be 14” thick. It was not a good day when I figured out it was much thicker than the first wall. After an hour and a half (and throwing my breaker a few times), I made it through the wall. The drill performed 100% the way I hoped it would and it was immediately thrown in the trash can after. This was honestly one of the most dangerous things I’ve ever done and I’ll never do it again. But as for the product- 10/10. Thank you for not making something that hurt me. Recommendations from my experience: - Mount the base to the wall using 1/4” tapcon screws at least 4” long - Use water (I used a generic spray bottle) throughout the drilling - Be prepared to spend an hour or more trying to remove the concrete plug if you have to drill more than one hole - Hire someone to do all of this because it’s incredibly dangerous

Excellent core drill, very reliable, the price is very good.

I used this today to drill 4 holes through a stone foundation in PA. I have no idea what the exact name of the stone is but there' a reddish field-stone that is so hard it's like granite and I was able to do the holes 100x easier than the old way I would have done it which is to use a hand-held core drill. This was so much more pleasant to turn a crank rather than hold the drill and safer too. One imperative tip for anyone using this core drill is to fasten the drill base to the wall or floor using multiple bolts. If you only use one anchor it will slightly deflect while you're drilling and the bit will bind. With multiple anchor bolts (I used three 3/8x4" tapcon bolts) the base will not deflect and the drilling is very easy. If your wall is greater than about 18 inches thick you will need to stop mid-way and add an extension. The bits tend to cold-weld to the drill spindle and the way to fix that is to put a giant adjustable wrench on the core drill bit and hit it hard with a drilling hamer to shock it and it will unscrew. It needs to be a really hard hit, plan on the wrench to go flying during the process but it will separate the bit from the spindle.

Several comments. Poor manual written by a lawyer. It was missing the following key information. They provide a couple of hose assemblies as shown in the attached pictures. The hose that is attached to the drill has a quick-connect fitting. You need to buy a Gardena quick-connect set shown in the picture to use one fitting that will allow you to connect their quick-connect to a garden hose. I pressure tested it, and it holds pressure at about 60+ PSI. (My garden hose runs high unregulated street line pressure.) I'm not sure what they thought we were supposed to do with the clear hose. One end can slip over the quick connect but I couldn't figure out what to do with the other end. It doesn't connect to a garden hose. No explanation in the manual. The manual does say the max water pressure is 0.12 MPa. That converts to 17 PSI, which is pretty low. I suspect this reduces the water flow to a manageable level so it isn't spurting everywhere. To reduce the pressure I am going to use an RV (Recreational Vehicle) garden hose water pressure reducer with gauge as shown in my picture. The drill has two speed settings. #1 is low speed at 159 RPM. #2 is high speed at 292 RPM. The manual doesn't say which is which, and they sound the same. To switch between them, you unplug the drill and then hold down on the trigger while turning the selector knob. It is otherwise locked, and I about broke my new drill trying to figure this out since it isn't in the manual.

Elle a déjà bien morflée depuis sa réception. idéale pour les passages de canalisations en 100 mm ou de fils électriques avec une fraise de 60 mm avec une profondeur de 400 mm.

Qualidade preço bom

Machine impeccable ... Dommage que le sais pas faire de biais... Un peu lourde aussi

Matériel amateur qui pour ma part a fait le boulot perçage dans 22cm de béton avec un trempant diamètre 132mm, l’embout pour le raccord à l’eau correspond au embout standard.

Ottimo prodotto!Forato un muro da 60 cm circa in pietra(con aggiunta di prolunga) senza problemi.Molto soddisfatto!