Car Shark Fin Antenna Cover, Roof Aerial Base AM/FM Radio Signal for Car SUV Truck, Vehicle Shark Fin Shape Cover with Adhesive Tape, Car Accessories Antenna Replacement Fits Most Cars (White)

It arrived promptly & in good condition, then we went into deep freeze weather so I could not try to install it until today and missed the return deadline - which was today.Know that it is a very light blue color. It is wide enough but an inch too short to fit the antenna on my 2017 Ford Edge.When I reorder I will also purchase some adhesive, this comes with a few, very thin, double sided foam tape pieces cut to fit the cover.

Absolutely does not fit a 2014 Hyundai Sonata. Flipped just the plastic piece off the top while trying to get snow off. Ordered this, after saying it was confirmed a fit. Would not seat properly. Even removed rubber gasket and it still would not work. Returned it.

My teen daughter has a 2016 Hyundai Elantra, think base model maybe the one above that. I didn't realize this cover easily coming off on Hyundais was a thing, until I had to search for the replacement. Firstly, if you are a new Hyundai owner, I'd recommend avoiding automatic car washes. But, if you're here reading this, it's probably too late.Two, if you are looking for this part, be sure you measure and look closely at the inside of your antenna. There's several different variations for them apparently.The type in our vehicle, that square-computer chip thing in the middle is twisted so it looks more like a diamond shape. Most of the parts I've seen have it look like a square shape. Some have another square above that, and some have a space for a gps tracker which is a big green tail type thing sticking out of the bottom. The part number for the one I needed, the diamond type shape, is 96210-3x100. And, it's about impossible to find, unless you buy the whole antenna assembly which is what the part number is for I realized, and I've seen anywhere for 80.-200.+ dollars. And, to do that, you need to remove the headliner, and replace the whole antenna assembly from inside the vehicle. And I really don't want to spend that much money for just the plastic piece on the outside that is very likely to fly off again at some point in time. Sorry for the novel, just trying to help out anyone in the same boat.With a really rainy week coming up, I went ahead and ordered this one. Dimensions seemed to fit and I was hoping I could modify it a bit to make it work. I gut the inside. I cut out the screw parts, which I kind of regretted after the fact. So be sure to check the screw parts on your vehicle. They will break off differently and may work out ok for your situation. I ended up having to cut the ones on the vehicle as well to get the cover to fit on more secure. Both easily cut off with small wire cutters I had. I then used some JB Weld to secure it to the car. The fin cover itself looks fine. The JB Weld was an absolute mess, and you can see how messy it is all over the cover. My daughter was ticked, told her oh well do it yourself next time and do better :) It should scrape off with a razor blade. It's been a couple weeks now, and it's staying on and secured. But it isn't seated completely, when I pushed it down while waiting for the weld to cure, one side would pop up a bit. So my next step is to try some black flex seal tape to hopefully fill in the small gap on the side and further secure it and protect it from the elements. So overall, this worked fine for me. None of the issues I've experienced were due to this part here. I'd recommend it, you can probably make it work, just may have to get creative with it.

Even though I was told it does, the item does not fit my 2021 Hyundai Tuscon. I didn't try to put it on within the given return window timeframe so am unable to. It did not cost much but I am very disappointed that it went to waste. I do not recommend purchasing this in any way, unless you want to be frustrated and al.ost flip your lid

Quality is fine but does not work for Kia Sorento.

The only reason I gave this five stars was so that it would be at the top of the listing. Everyone knows how this works. This shark fin does not fit a 2016 Dodge Journey as it says it does. I am very good at mechanical work handy work Electronics plastic welding you name it. I was able to cut apart many of the inside parts and fit it over top of the antenna and it still did not get a complete seal.

Does not fit a 2017 Ford Explorer XLT. Oddly, the plastic cover ripped off during a drive thru car wash. The antenna functions normally, no problems. But, being exposed may eventually cause problems. I needed a cover only option. This one does not fit over the existing footprint so I had to modify it a little and use a butt load of glue. I took the rubber seal off, unscrewed the three screws to release the plastic base piece, reinstalled the rubber gasket and placed it as best I could over the existing antenna.Glue, glue, and more glue. Took it on a test drive up to 60 MPH, checked it, it was still in place and had not budged. Not sure how long this will last but I’ll take what I can get for $9.99. Why don’t car companies make the plastic covers for these things? Looks a little messy as the glue dries, but it will clean up later.

Does not fit Genesis G80. It does seem to be made well if it does happen to fit your car model. Rating is for fit on my model and not for quality of materials.