TruGlo Low-Profile All-Metal Construction Glo Dot II Universal Fiber Optic Sight for Plain Barrel Shotgun, 12 & 20 Ga/.410 Ga, Green/Red

This fiber optic sight fits the Winchester 12-gauge shotgun perfectly. Once clipped into place, it stays there without falling off. Color is very bright in the sun. It aligns perfectly with the bead sight and locks into place.

For the money, this thing is a great bargain. BUT: It is NOT, NO, NOT, all metal. It’s a high grade plastic and it seems to be very sturdy. I’m going to buy a few more to upgrade some of my shotguns. It beats the heck out of a silly little bead!

I got this sight for an older, JC. Higgins, single shot .410 shotgun I've had for many years. It is a simple design with a bead sight. This sight is a great upgrade for the single bead and works great for most lighting conditions except very low light and darkness where it's the same as a bead sight. This is not a night sight, it is a fiber optic, but in daylight and room light this sight works really well. It's very bright. I would love to see TruGlo put this out with a TFO tube. It is easy to put on if you just read the instructions and follow it. Hold the sight over the barrel behind the front bead (meaning toward the breech end of the weapon. Place the end of the sight tube that is closer to the breech against the barrel and hold the sight at a 45 degree angle with the muzzle end of the sight barrel up. Then holding the breech end of the sight barrel against the weapon barrel push down and back on the front of the sight at a 45 degree angle until the back end of the sight barrel snaps over the weapon barrel; keep up pressure as you continue to press the front of the sight barrel back and down to get the rest of it around the weapon's barrel. Just make sure you don't press on the fiber optic tube itself. It will snap right into place. Lastly use a flat blade screwdriver to push the sight forward so the front notch is centered around and against the front bead, being careful not to scratch the weapon's barrel. You might have to rotate the sight barrel a little to straighten it out so the fiber optic tube lines up straight with the sight line of the weapon.

Got this for my new shotgun because it was not that expensive and the brass bead on my shotgun was plain. Simple to install and looks pretty cool, especially in daylight. It is a little hard to see the green dot in lower light conditions, but its not that bad. Worked well at the shooting range and it worked awesome when I went shooting out in the desert.

I had previously installed one of these on my Mossberg 500 12g and was pleased with the results. It does take a little trial and error to hold the sight at the right angle and push just right, but it doesn't take long to be agle to pop it in place. Because the diameter of the .410 is so much less than the 12g, it's trickier to get the walls to spread. I actually pushed at the wrong angle and accidentally bent one side, but I got a pair of needle nose pliers and bent it back enough to find the sweet spot to get it on. Whateveer that plastic is, is a miracle. I haven't had a chance to fire the gun yet and see if it truly holds its place, but once it's properly mounted, it fits so tightly, it doesn't seem like it will be going anywhere from the gun's recoil. UPDATE: I've fired the shotgun about half a dozen times now and I dont' see a hint of movement. The fiber optic bead is bright red in the daylight and about the same size as the factory bead. I am thoroughly pleased. One note: This sight is harder to put on a .410 barrel than a 12g, so pay close attention putting it on. The plastic is quite firm, but it's also unforgiving. Get it right the first time,

If there was anything less than 1 star I would give. This item is a piece of trash. When I snapped it onto the barrel as instructed in the direction both sides broke off and fell to the floor. Don’t by the product ever.

I purchased two of these, both for Mossberg 88 12ga Tactical Shotguns. They are very bright, and work well. My wife and I completed a 4 day tactical shotgun class at Frontsight, and hers made it through, but mine the fiber optic came loose and was lost on the last day. These classes are always a true test of gear, and it seems that these made a 50% showing.

Bought this for my Rossi Poly 20 GA. Really easy to install. Snap it on the barrel and it actually fits really tight! I ended with a sore finger tip when I had to peel it off the barrel because I had it ahead of the bead rather than behind it. I can definitely see better. A lot better in low light. Should be great for Dove or Deer.

20ga baikal single sot works nice

Perfetto per SXP cal.12,facile installazione.

Bei eine Flinte ohne Zielschiene oder Befestigungsmöglichkeiten für andere Zielmittel ist es ein sehr guter Behelf. Die erstaunliche Leuchtkraft erleichtert den schnellen Schuss beachtlich. Vielleicht sollte man das Teil später mir einem temperaturfesten 2k-Kleber dauerhaft fixieren.

Way easier so see than ball sight, quicker to sight. Placed mine in hot water for couple minutes made for easier install. Make sure you line it up before it cools down because this baby holds it's position really well once cooled down. Good for securement, but hard to adjust when cool. Bought second one for pump.

Parfait, acquisition rapide même en condition de luminosité faible, fait mieux qu un grain d orge seul. Je recommande largement