🚀 Elevate your IoT game with ultra-efficient, long-range wireless power!
The LILYGO LORA32 T-Beam ESP32 SoftRF Development Board combines a powerful ESP32 MCU with a 915MHz SX1276 LoRa chip, delivering long-range, low-power wireless communication. Featuring 4MB Flash and 8MB PSRAM, it supports complex programming tasks, while flexible antenna options and a CH9102 serial programming chip streamline development for cutting-edge IoT projects.
| RAM | LPDDR2 or LPDDR3 |
| Wireless Type | Bluetooth |
| Brand | LILYGO |
| Series | ESP32 LoRa Development Board GNSS NEO-M8N & NEO-6M |
| Item model number | SoftRF |
| Operating System | FreeRTOS |
| Item Weight | 2.89 ounces |
| Product Dimensions | 6.85 x 6.1 x 1.65 inches |
| Item Dimensions LxWxH | 6.85 x 6.1 x 1.65 inches |
| Processor Brand | Espressif |
| Number of Processors | 1 |
| Manufacturer | LILYGO |
| ASIN | B09VLFQQG4 |
| Country of Origin | China |
| Date First Available | March 11, 2022 |
R**C
Nice little device! great for hobbyists and doesn't require a lot of expertise.
Nifty little device. Seems solid. Documentation could be better, but it's a sufficient pointer to online stuff. Need an enclosure. Reasonably priced for what it is. Nice and small too! Comes plug and play so its easy to get going.
M**!
Great device
Great meshtastic device. Work great
M**H
Easy mode
Super easy to setup, I'd call it easy mode. Solid build quality and has been happily running since setup. good value for low effort entry, but it's almost too easy so if you're looking for a fun day project, this probably isn't it. took minutes to setup.
R**E
Works, but only after updating to latest firmware
If you use this board (firmware 2.0.10) with the current version of meshtastic Android app it will not work properly. Mostly Bluetooth configs and messages will fail with the occasional success when you cycle the connection. That said its easy to correct but the meshtastic website will lead you wrong. If you update the firmware with the web installer the device will be dead (but not bricked). As someone mentioned in the Q&A you'll need to do this firmware upgrade with the python cli firmware instructions (esptool) it's fairly straight forward. Just follow the meshtastic website instructions. Note: if you are on Linux you may need to gain access to the serial port. Most distros make the group dialout owner so you can just add yourself to the group. Or run it all with sudo. Esptool will run several times but once it finishes the devices will work very well. I purchased 3 with oled soldered and all worked well after successfully updating the firmware. Just wish I hadn't wasted hours trying to figure out why the installed firmware had issues and why the meshtastic web updater kept leaving me with dead devices.
B**T
Preloaded firmware for soaring.
This board worked out of the box. I was surprised that it came preloaded with firmware appropriate for use in gliders.
A**X
Works great
A little pricy to buy but a lot faster shipping compared to ALI. Flashing worked fine, and the node is up.
F**Y
Very cheap construction, hard to gather I would figure for an inexperienced user.
These units do work on Meshtastic (make sure you order the right one if it is the way you go or you will need to reflash it). However, they are cheap and Lord forbid if you want to put it in some type of case or before you get it n the case something brushes up against the cheaply soldered on components. Person setup for got bottom switch barely tangled on sweater, fell off board didn't even pull on it. The only reason I am ordering a 2nd is because the person who wanted me to get this setup for them is adamant this is what they wanted. I prefer my Wisblock stuff to this by leaps and bounds.
T**5
Great addition
Lilygo t-beam just works. Easy set. Works well. Note: you need thebuttonless type of battery.. additionally the longer antenna for better reception. Just remember they are line-of-sight. Recommended
Trustpilot
2 days ago
1 week ago
