Oshlun LG-M01 Miter and Portable Saw Laser Guide, Miter & Portable Saws , grey

I’m quite happy with this accessory. It was easy to put on and doesn’t get in the way of anything. I put it on my 10in Bosch glide saw. I didn’t have high expectations for this but it is extremely accurate. I never take the saw out of my shop but I could maybe see on a job site or having it outside, that the laser might be hard to see. I haven’t tested this but in my shop, I have no problems at all seeing it. I didn’t want to go through the hassle of putting on a shadow line accessory and this seemed like a good value. I thought maybe it was going to be too large but like I said, it fits very well and doesn’t get in the way of anything. It’s been going strong for 6 months now and I’ve had no issues. Again, I haven’t tested this theory but I think it’s design will allow it to be used on just about any miter saw.

First let me say this is the 2nd Oshlun Saw laser device I've purchased as the first has worked flawless for the first year on my Miter saw. This one I just installed on my 7.25" Circular saw, and it also works flawless. There is no trial guesswork for deciding where to engage a straight line, sawing is then accurate. I highly recommend these lasers, and they come with spare 357 batteries also! This is a great useful tool that enhances your precision cutting.

Many times on my old (30yrs) Dewalt DW-705 Miter saw I had wished there there was a laser to pinpoint the exact cut line, like most modern miter saws have. I've seen the 𝐎𝐬𝐡𝐥𝐮𝐧 𝐋𝐆-𝐌𝟎𝟏 𝐌𝐢𝐭𝐞𝐫 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞 𝐒𝐚𝐰 𝐋𝐚𝐬𝐞𝐫 𝐆𝐮𝐢𝐝𝐞 on Amazon for a long time and finally decided to try it on my DW-705. In past reviews I've read some comments about the laser housing being too thick and rubbing against the blade guard housing. Ohslun mentioned that this newer model was thinner and fit more saws so I thought I'd give it a try. Installation was as simple as removing the orginal spacer and replacing it with the 𝐎𝐬𝐡𝐥𝐮𝐧 𝐋𝐆-𝐌𝟎𝟏 𝐌𝐢𝐭𝐞𝐫 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞 𝐒𝐚𝐰 𝐋𝐚𝐬𝐞𝐫 𝐆𝐮𝐢𝐝𝐞. I tightened down the blade retaining bolt and fired up the saw. My first reaction was well, the laser works, looks accurate but it was making a heck of a noise and seemed to be vibrating a little. I stopped and unpluged the saw and removed the laser guide. On close inspection of the laser guide I could see that something was rubbing against it (flub). I completely removed the blade guard to see what the situation was by removing the 3 T30 torx screws holding the blade guard assembly to the saw. What I discovered was that the laser guide was rubbing in one little area of the blade guard housing. Now that the laser guide had scrape marks on it I couldn't return it so I started thinking about a fix to see if I could add some clearance between the 𝐎𝐬𝐡𝐥𝐮𝐧 𝐋𝐆-𝐌𝟎𝟏 𝐌𝐢𝐭𝐞𝐫 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞 𝐒𝐚𝐰 𝐋𝐚𝐬𝐞𝐫 𝐆𝐮𝐢𝐝𝐞 and the blade guard housing. The fix was easier than I figured it would be. One little flat washer mounted at the front and the rear blade guard mounting screws in such a way as to add 𝒋𝒖𝒔𝒕 enough clearance between the blade guard and the 𝐎𝐬𝐡𝐥𝐮𝐧 𝐋𝐆-𝐌𝟎𝟏 𝐌𝐢𝐭𝐞𝐫 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞 𝐒𝐚𝐰 𝐋𝐚𝐬𝐞𝐫 𝐆𝐮𝐢𝐝𝐞 so that there was no more rubbing between the two surfaces. I Fired up the saw again and this time everything was nice and smooth with a clearly visible red line at the point of the cut. (I purposely positioned the laser line 𝒋𝒖𝒔𝒕 a bit off the pencil line to show everything is square). Lastly, I also discovered that a "thin kerf" blade may need no modification at all as I noticed more clearance between the 𝐎𝐬𝐡𝐥𝐮𝐧 𝐋𝐆-𝐌𝟎𝟏 𝐌𝐢𝐭𝐞𝐫 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞 𝐒𝐚𝐰 𝐋𝐚𝐬𝐞𝐫 𝐆𝐮𝐢𝐝𝐞 and the blade guard.

I was expecting to return this as soon as I got it. I looked it up on YouTube and for a good setup video. I expected the worst after seeing some reports that it wouldn't work on my Bosch 12" miter saw I went from a plastic encased tool to a working laser in 15 minutes with the most difficult part being finding my hex wrenches (Neatness is not my strength) It has worked flawlessly since. Thank you Oshlun!

Miter saw laser guides work great on both miter saws and redial arm saws. They work by shining a thin laser on the side of the cut line. It is mounted on the arbor next to the blade. When the saw blade spins the centrifugal force causes the beam to shin and when the blade stops spinning the beam switches off. This is great for lining up your cut to the blade and for checking the alignment of the saw. I bought two of these guides. Both guides displayed a convenient line for cutting. The line was bright enough indoors but difficult to see in the bright sun. I expected this. I noticed that on both of my saws the laser light stayed on after the blade stopped spinning and eventually turned off. This situation was not always noticeable unless the blade stopped so that the laser beam shined down on the table. There is no on/off switch except for the internal one built into the unit. The only way to manually turn off the beam is to remove the laser guide, dust cover and batteries. The construction of this product is poor. The case that covers the batteries and laser unit is pressed sheet metal. The center of the cover that slides over the arbor has rough edges that hung up on the arbor threads when I installed the devices. By spinning guide like a nut I was able to thread them onto the arbor. I have been using these laser guides for six months and both devices have stopped working. I removed the units from my saws, checked the batteries and all the batteries were dead. I suspect it is because the beam stayed on after I finished my cut. Wood working is a hobby for me. I am not using my equipment on a daily basis. After six months of use the batteries should not be dead. I have the Irwin Miter Saw Laser Guide installed on a compound miter saw. This laser guide is still working after eight years. I have changed the batteries once in this device. Unfortunately Irwin does not make a guide for a 5/8” arbor. I would not recommend this guide because of the poor quality and short battery life.

I purchased the Oshlun LG-M02 laser guide for my AEG PS-305 DG 12" compound mitre saw. The existing laser guide on the saw had broken and was no longer available. The Oshlun laser guide works well on this saw, however I had to replace the existing counter-sunk M10 left hand thread arbor bolt with a non-countersunk bolt (30mm worked well). Based on my personal experience, I would recommend this device for the AEG saw if the original laser guide part fails.

O produto é muito robusto e cumpre o que promete. Muito preciso na indicação da trilha de corte. Apenas aconselho a verificarem a compatibilidade com a sua esquadrejadeira, no meu caso, uma Stanley SM-18, tive que fazer pequeno (0,5mm) ajuste na arruela do disco, para que o laser desse o aperto necessário ao disco. No mais, funcionou com muita precisão.

Funciona perfectamente en mi sierra ingletadora

Qualité du trait impressionnant montage simple avec bague de adaptation pour l Europe

Works way better than i thought. It makes a nice line exactly where it’s going to cut. Just slightly off to the side. On the left. But seriously, it’s way better than i thought. I love it. It’s actually useful. Great device. Works good on the bosch glide saw.