Grafix Ink-Jet Printable White Opaque Shrink Film - 8.5"x11" Print, Cut and Shrink It to Create Jewelry, Embellishments, Tags,Ornaments. Shrink Plastic is for Kids of All Ages,Pack of 6

*UPDATED: JULY 2020* This product is AMAZING! I have been using this product for a few years now, and I have loved the results I have gotten from this product. Continue reading for my tips and tricks when using this product! First of all, I print out my designs from my computer to my Canon MX922 printer. I use the Photo Paper preset, but the Glossy Photo Paper preset works the same. A VERY IMPORTANT tip is to lighten the colors. The percentage of lightening the colors can vary, but know that the more you bake your designs in the oven, the darker they become. When I used to bake them for 3-4 minutes, I lightened it by 50%, but now when I bake them for 8-10 minutes, I have to lighten them by about 70%. Second, after I print them, I move on to cutting. The cutting process is self explanatory, but it is also important to HOLE-PUNCH before you bake if you are making keychains. Another thing would be that my hands often times get sweaty when cutting, so I HAVE to wear gloves, since it can leave a yellow stain on your designs. Third, its time to bake! (The most enjoyable part, but can also be stressful for your first time) I pre-heat my oven to 300 degrees, put my designs between 2 pieces of parchment paper, and put them into the oven. People say it takes 2-4 minutes, but for me, it actually takes from 8-12 minutes. It really depends on the size of your designs, so you will have to experiment. After doing this many times, I realized that the longer they are in for, the less imperfections that they have. Again, the most important thing is TRIAL AND ERROR, so find that right temperature for you. Another tip would to be to NOT FREAK OUT. The main reason why most of my charms failed in the oven step was because I was so anxious if they were going to over bake. However, this ALWAYS led to me removing them too early and having failed charms. Just remember that over baking is WAY better than under baking, so there is no reason for you to worry. I did read that someone said that they can burn, which I never encountered, but be cautious! Finally, I quickly remove them from the oven, flattening them with a flat pan/plate. BE WARNED that they cool down VERY quickly, so flatten them quickly. Next, I apply DecoArt Americana Triple Thick Gloss Glaze for one main reason. If you use Mod Podge Dimensional Magic, using it by itself without an under coat will probably make your design smear. This product does make the colors more saturated, so be aware of that! It isn’t my favorite glaze because of it saturating the colors, but I don’t know of any other gloss so I just gotta make do with what I have. I leave it to dry for the whole day or night (10-12 hours-ish), and then move on to using Mod Podge Dimensional Magic. I have to say, Mod Podge Dimensional Magic is very stressful to use. Lots of my charms have failed because of it. The air bubbles are very stressful, but I typically use a needle and toothpick to pop the big ones. If there are some small ones you want to take out, you can scoop them out with a sticker note or paper, which works most of the time. I also had times where the liquid overflowed, so make sure to not overdo it. Another tip I have for this product is that whenever the liquid covers small spaces/crevices, I wait about 1-2 hours for it to set, and then go in with a toothpick to cut the liquid that has fallen in these areas. Using this product can be very stressful, but when done correctly, the end result will be very nice and will leave you satisfied. I let it fully rest for 12 hours before I call it finished. Overall, this product is really fun to use, especially for those who want to get into the art of making charms. I am super satisfied with how my charms have all turned out and very excited to continue making more. A final tip to you all would be to not give up if you mess up. The mistakes are what allows you to learn and become better at doing this. I hope this review helps someone, as knowing some of these things from the start would’ve been so helpful to me. I know this has been long, but thank you so much for reading this! 💖

This generic brand of the classic Shrinky Dink is a great product, especially since the new version of Shrinky Dink material is of a lesser quality and does not produce good results. 1) I found that the plastic sheets feed thru my Epson Artisan 830 without a problem. I set my print settings to print on Glossy Photo Paper. With normal quality. The print was very clear. 2) The Images should be lightened by about 50% since upon shrinking the colors with become very intense and possibly different than what you have printed. I also let the printed film set for a few hours to dry completely before cutting and backing. 3) I set my Oven to 325 Degrees F. and baked my designs for 3 to 4 minutes on a piece of Parchment Paper on top of a metal backing pan. I watched to make sure that the designs I had created had settled almost completely flat before removing them from the oven, Note: Don't wait too long to remove them from the Oven or they may start to burn. Upon removing, I pressed the pieces completely flat with a spatula then after 1 minute I flipped them and pressed them flat again and let them sit for 3 minutes before removing to cool completely. 4) This film will not shrink up to be completely smooth. However it will have a slightly rough texture which I did not mind. The designs should be sealed with an Inkjet Sealant like PremierArt Print Shield Spray 400mL so that they don’t smear when wet. If you wish your designs to have a more smooth texture then I would follow this sealant with something like the Krylon 12-Ounce Triple Thick Clear Glaze Aerosol Spray Product. This works very well. I placed three coats of this sealant on my designs and they came out relatively smooth and a little shiny. I gave this product 5 stars and have now purchased them again. I have also purchased the clear inkjet product in the hopes of making some sun catchers. Please let me know how I am doing by voting “YES” if you think that my review helped you.

I am a former user of Shrinky Dinks and after having a horrible experience with their support on their faulty product, it has prompted me to look into other products. Which I had been aware of this product when Joann's had started to carry it. I have basically every pack they carry, but this one. I received it in the mail yesterday and compared to the two, there is really no difference. Looking at the sheets side by side before printing and cutting, Grafix had a smoother more matte finish, while Shrinky Dinks, you could see manufacturing lines in the finish. But they both bake equally the same. I did notice Grafix does have a slightly rougher texture than Shrinky Dinks, but is a minor oversight. Also, Grafix is made in the USA and I am more inclined to purchase from a company that oversees the whole process and reading from a previous review, will admit fault in product versus putting it on the consumer. The instructions are precise and very thorough. I noticed they suggest using an acrylic sealer, which I went to Joann's and Michaels in hopes of finding the sealant they recommend. (A brushable one) And no dice. I do have several other acrylic sealants in my studio that I plan to test out with this and will post my follow ups as to what worked and what didn't. I did try my Super Gloss Mod Podge and that worked wonderfully as always. I did try Martha Stewart Multi-Surface Durable Gloss Finish and that just pulled the ink color off. Doing a second coat of Super Gloss Mod Podge did make the finish not look so rough. I also cut a corner of Grafix and Shrinky Dinks, baked them both at the same temp, same amount of time and Shrinky Dinks. Both side to side, Shrinky Dinks has a off white hue to the shrunken piece.

Like a lot of comments here, I bought these as an alternative to Shrinky Dinks. (Shrinky Dinks changed their inkjet plastic formula and they kind of suck now.) I kept my expectations low and tried my hand with this new plastic. For people too lazy for a thorough review: Overall an ok craft product. Silhouette cutting is doable. Once baked the plastic is slightly thinner than brand plastic and flexible. Fuzzy texture on both sides. 3.5/5 For the OCD crafters who need a thorough review grab a snack and get comfortable, because this will be a long one. lol ----- My experience: **Printing:** - As recommended, I lightened my images by 50% and printed on the standard setting with my Canon inkjet printer. No smearing, no paper jam. Print quality will probably vary depending on your printer, but mine was great. So far so good! **Cutting:** - For those of you that are looking to cut these with a Silhouette machine: it's doable, but you'll need to work to get the results you want. Keep in mind that I do not have a deep cut blade, so for those of you that do check out the recommended settings in the asked questions section. - I tried my first sheet with the basic shrink plastic setting (the one Silhouette expects you to use with their brand sheets) and it took forever. I ran it through my machine with double cuts 8 times and it never cut through. I ended up having to snap the pieces out. This wouldn't be a big deal if the back of the sheet wasn't covered with whatever they use to make the plastic printable. It leaves a thin layer around the edge, like the thin membrane you find around hard boiled eggs, so I trimmed off what I could with scissors and ended up completely pulling this layer off on a couple of my other pieces. -- This will become a problem later, but can be avoided. - My second run went a little more smoothly setting my blade to 10 with the shrink plastic setting. Had to run it about 10 times and it still didn't cut all the way through. Snapped my pieces through, trimmed whatever thin skin again and got ready to bake. **Baking:** - I preheated my oven to 350° and baked my first batch for about 3 minutes. They shrunk slowly and got stuck in the "cup" position at around the 3 minute mark. No worries - I added another minute and they flattened out ok! I moved them to my counter and pressed them down with a cook book. First batch good to go. - Second batch shrunk faster since the pan is already hot from the first run. Remember when I said I peeled off the backings on some of my pieces? Those pieces flipped and curled in on themselves on the blank side. Might have been able to uncurl and flatten them out, but the plastic cools off so quickly outside of the oven that I took the loss. Keep in mind: this plastic CAN NOT be reheated once the plastic cools like the Shrinky Dink brand, so act fast if this happens. - For my third batch I ended up laying a second piece of parchment paper on top of the pieces to keep them from curling, like the instructions recommend. Shrinks perfectly fine without any curling and worked on the pieces without backings! **Results:** Size and consistency: My pieces shrunk about 50%. I made a 5inch (12.7cm) test piece that shrunk down to about 2.5inches (6.35cm). Turns out this isn't really as helpful as I was hoping since the 9 pieces I cut out of a single sheet ended up having different levels of warping. Some of my pieces came out fine, while others were slightly stretched or squished. This might not be a deal breaker if you don't care about consistency, but definitely will be if you're buying this to make matching earrings or pins for Etsy. Another thing to note is that this plastic is slightly thinner than Shrinky Dink plastic. It's thin enough to have a good amount of flex. (See photo) This could be a winning or losing point for crafters. Long, narrow pieces have a lot of flexibility and small round/square shapes will have less flex, but still have a bit of bend. Flexibility might be great for accessories that need to hold up under some pressure, like key fobs, but might not be great if you're looking to have some solid hanging charms. If you want a thicker finished product, buy Grafix' regular non-inkjet plastic. Texture: (See photo) Like other comments have mentioned, the pieces will have a textured front and back from the printable material coating the plastic. If you end up peeling some of it away and bake the pieces, it will be really obvious. The texture will also be present around the edge. You can take an emery board and file off any edge fuzz or uneven plastic, but unless you're aggressive with your sanding you won't be able to have a flat clean edge like you would with Shrinky Dink plastic. Sealant: I think this really depends on your printer ink, but I used a matte fixative and it sealed my prints ok. I'm currently waiting on the layer of mod podge to dry, but it seems to be doing ok without any running. I'll update in the event that the mod podge tears away from the surface, but I doubt that it will with how textured the baked product is. lol ----- Wow you made it! Personally, if you're buying this to use for craftables with your kids, it's great. If you're looking to use this to sell on Etsy, I'd buy it with caution. Hope this review was helpful ^^

New to shrink plastic crafts,this is the second brand I tried, super happy with these though! Expensive for a craft supply but well worth the price. The printable shrinky dink brand sheets do NOT take my HP printer ink well and keep smudging even though I let it dry for an hour before touching. This one dried within minutes after printing,no smudging before or after baking, very nice! I read reviews about this particular brand of paper and decided to reduce color saturation by only 30% for printing, that worked perfectly for me. They turned back to the original color after baking, I am super excited!! I baked these at 350° for 3 mins sandwiched between two cardstock papers on a cookie sheet. They come out flat without needing to be pressed flat with a spatula. But they don't shrink as much as the shrinky dink brand. I scale them up to 200% so they can shrink down to the size I want. I tried scaling to 300% like I did for the shrinky dink brand and they were still huge after 3 1/2 mins in the oven! So scale to 200%, bake at 350° for 3 mins is perfect for this brand. Now when I said NO smudging before or after baking, that is 100% true. BUT when adding Dimensional Magic to make these dome, these DID bleed, especially the black ink. So make sure to seal, SEAL and SEAL, before adding the dimensional magic. Let it dry after each coat of sealant. I blow dried in between because I lack the patience. Then after the final coat of acrylic sealer, I let it dry overnight. Check that it is completely dry before adding the dimensional magic. Have no success cutting it with my silhouette cameo 3 but that's okay, maybe when I upgrade to cameo 4 I will have better luck. Love these, I just wish they were cheaper.

I wish there had been a review like this prior but I guess I will be the first. So what is the true difference between the two types of papers and how do sealants react to them as well. Well, I would like to present my following findings. Grafix Printable Shrink Paper - easy to grab by printers and ink drys on it easily (both inkjet and laser) - bakes fast and easily flattened with pressure when coming out of the oven - when baked and cooled the paper has thickened and is very sturdy - will not chip or bend without real force - if sealed with regular resin or mod podge 3-d dimensional it will look great and stay intact - sealing with UV resin will cause the paper to bend due to the heat and can curl the entire image Shrinky Dinks Printable Shrink Paper - the paper is a little more difficult to grab by printers and the ink will take longer to dry (both laser and inkjet) - bakes faster than Grafix but can smudge if you flatten it too much out of the oven - it must be done slower - the paper bakes thick but not as thick as Grafix, it is also a bit more bendable than Grafix - when it comes to sealants this paper is actually stronger than Grafix - whether it be UV resin, regular resin, or mod podge 3-d dimensional, this paper will not bend or curl during the curing process with any of these methods So before you make your purchase be sure to consider the following - they may come in handy.

For some reason one of my reorders of this package came in a non labeled clear envelope. That particular pack didn’t shrink evenly and was much less smooth once shrunk. I think it might have been a different brand sold as name brand. I threw it all out because it was so inconsistent I couldn’t use it for sellable pieces. The next pack I bought was labeled and shrinks just as expected. Very weird. Watch out for unlabeled packs. The actual name brand of these print and shrink beautifully.

I have used this product once (I just ordered my second batch today) and since it was my first time, I was super paranoid and read and followed the directions painstakingly. Because of this, I was able to create very pretty, colorful keychains that sold well at the event I took them to. All six sheets came out well. I do definitely recommend coating them with mod podge to seal the color. The texture is rough so if you're making something you would not like to be rough, this would be another strong incentive to use a clear sealant. I obtained perfectly flat pieces by waiting for them to flatten out in the oven and following up by squashing them down with thin a piece of smooth, coated cardboard and applying force evenly over it with something flat. If a rogue piece was too curled up out of the oven to squash down, I simply pulled it flatter with disposable wooden chopsticks before I put the cardboard down onto it. If you're worried you'll miss an important step just have a short checklist at your elbow to make absolutely sure that you lightened your image by 50% BEFORE PRINTING and punched any holes BEFORE BAKING. Those are the two big things you don't want to forget.