Front Windshield Outer Door Molding Compatible with Chrysler Town Country

Fit out van perfectly and was easy to install.

It is a perfect fit. It is not easily installed.

I only needed the driver side panel and it fit very well. It was hard to install. I had to trim the small pieces of foam on the back so it would slide on while pushing and aligning it . Once fitted on the screw on the back fit very well.

The pillar piece flew off our van driving in some good ol’ Kansas wind. I called our local Dodge dealer and was quoted $160 for a replacement piece. Sticker shock! Thankfully, I had this in my Amazon cart and went this route instead. The pieces were delivered quickly and I set to work right away installing it. I needed my drill and a hex bit to remove a tiny screw on the inside of our door. Then, before I removed the backing of the adhesive strips I did a dry fit test. Man! This bugger requires some strength and finesse to get it just right. Once I knew how it was intended to fit, the rest was relying on patience and persistence. A little contortioning as well, as I was practically hanging from our van door trying to slide it into place without breaking anything. My husband offered to help, but sometimes he doesn’t know his own strength and I didn’t want him to accidentally break the piece. I kept at it though. Finally, I got it worked down just right and the post at the bottom into position. Reattached the screw to hold it in place, and voila! All done! I think it had to be tricky to install so it is less likely to fly off again. Other than that, I’d have given it 5 stars. Have fun!

I did not see any instructions, so go to Youtube and find one. There is a screw on the inside of the door than holds the bottom of this trim piece in place. Typically the remains of a cracked off piece of plastic from the old trim piece will still be held in place by this screw. Discard that piece of plastic, but re-use the screw. Don't peel all the backing from the adhesive strip before you install it; start removing it from the bottom, and peel just enough to have some sticking out. Then once the trim piece is in place, peel the rest. If you don't, it can stick to the car door during installation and cause some difficulty while trying to slide it down. Something was a little wrong with one of the tim pieces and it was very difficult to get it to slide down into place. I actually had re-apply the adhesive tape cover, and had to put a block of wood above and tap the trim piece it down carefully.

had to use a lot of pressure to make fit

Fit perfect

Shipped quickly. Easy to put on.

2 person job Good fit. Snug to install but that is what you want. I trimmed a little of the bottom of the foam for the T slots on the plastic piece so it easier to push down into the slots. The red tape areas are sticky foam so do not peel these before installing as you will stick to door and not be able to pull them down. Instead peel a little back from the lower end of the long tape and a little form the short tape at top and fold back like a pull tab that will be accessible after so after install you have a string to pull on after it is in place. Then after install and in proper position (before screw) you peel gently and red cover comes off/out nice x 2 areas and then you push down firmly to set the sticky to car. clean and dry car door portion first where tape will go. Get good alignment of T slots and then press in firmly in both spots to get it started in both spots. if you do not get both you are stuck and need to try again. 2 people needed. with 2 T started ok you still have a ways to go so setup one person pulling firmly on bottom (but not bending and other pushing carefully on top at same time (used bit of wood to not hurt fingers. Check screw hole to see you not go too far. Best thing we did was to add some hand soap to the 2 rectangles of foam around the 2 x T areas and on steal T slot on door as lubricant to help it move. I think this was super helpful. Good luck

Bought for my 2015 Caravan as one side piece had broke and was a perfect fit! Easy to install and looks awesome. Also nice having both sides in case the other one lets go as well.

Much cheaper than what Dodge wanted for just the one side. I only needed the left side but now I have a extra if the right side ever brakes off. The plastic quality appears to be near OEM and the preinstalled adhesive tape said 3M. Was easy to install and lined up with the factory mounting point. Good product!

Good quality

Driving down the highway and my wife goes "there is a piece of plastic flapping off the side of the van...op, it's gone". Bought this set and installed the side that went missing. Looks good. I mean, it's a caravan so who cares but missing big pieces of trim is a blatant "I don't give a hoot bout nothin".