Chicago Power Tools 39607 9-Inch to 10-Inch 8-Piece Waxers Bonnet Set

The quality of these bonnets for my buffer is good. They came packaged nicely and easily fit my buffer. They were easy to attach to the unit and worked as expected. I would purchase again if I need replacements but I don't anticipate needing any anytime soon. I will recommend these to my friends so they can have quality buffer bonnets for a fair price.

I read the reviews and most say these do not fit a 10 inch buffer but they do... It is hard to get them on but there is a reason for that.. to put one of the bonnets on, you need to start on one side and slip it over the buffer wheel, then pull down around until you get a 3/4 around... this is when you will think it does not fit... now while holding the side that is not over the buffer wheel, reach down under the side that is already on and you will feel the elastic pulled toward the center... pull it outward to the edge while pulling on the other side until you get the whole bonnet down around the buffer wheel... Now flip the buffer over and looking down from the top, pull outward on the part that is closer to the center while pulling the other side... keep adjusting it until it's centered all around the buffer wheel... You will notice after you get it on that the edge of the buffer wheel has been squeezed so it does not have an edge... it's rounded instead all the way around the buffer wheel... it has to fit tight like that so there won't be an edge because an edge will leave circles in your wax job... I used it on my 11 year old truck and my truck looks like new... it was very dull and I had also used can spray paint on it over the years... after buffing first with rubbing compound and then a wax after, it looks a lot different... be sure to use the dark blue bonnet after you remove the wax and it will put a deep dark polish on the finish..... Clean up: I put what I used in the washer, small load, cold water, and a little extra detergent... then in the dryer on medium heat... they look like they did before I used them now.

Good variety but quality is hit or miss The Chicago Power Tools 5–6" 8-Piece Waxers Bonnet Set is a decent starter pack if you just want a range of pads for your orbital buffer without spending much. It includes several bonnet types—typically terry cloth, synthetic wool, and foam—that handle both wax application and removal. They fit most 5–6" buffers (like Wen or Black & Decker), though some users report a snug fit that takes effort to stretch over the pad. On the positive side, they do work well for light polishing and waxing. The terry bonnets absorb wax evenly and buff to a nice shine, while the foam and wool pieces help finish the job. I machine-washed a few on cold and air-dried them, and most came out fine for reuse. The downside is inconsistency: some bonnets feel thin and wear through quickly, especially after a few sessions. The elastic edges can also loosen over time. For occasional DIY use—say, waxing your car twice a year—they’re fine, but not for frequent or professional detailing. Bottom line: a fair value kit if you just need extras on hand for your small buffer, but durability and fit vary. Expect usable but not premium quality.

The four applicator bonnets (light blue) are very thin; like see-through hospital hair nets or booties. Much of the material to be applied will end up in your foam base (if your polisher is like mine). The other 4 bonnets are of good quality and I have used them to was 3 cars and they are still in good condition and worked satisfactorily. This is a decent value set but I do not recommend using the light blue applicators alone. I place them atop another bonnet to use them, however they do not hold up and are single use disposable in my opinion.

You get 8 Bonnets for that price. The quality is much better than the bonnet I received with my polisher. I have read many reviews stating that it would not fit on a 10" polisher. They do fit pretty well on mine. Most of them are even quite easy to put on. The synthetic wool one is a bit smaller and was harder to put on but it fitted. I them measure the pad of my polisher it is 9.5" is diameter with 1" thick pad. I could not find a better deal for the price.

I love this package of waxing pads. I have a black and decker 6" orbital buffer and all of these fit and work well. I use New Finish Paste wax and the applicators are perfect at spreading/waxing evenly without too much being absorbed. The terry pads make it very easy to remove the wax as well. I haven't tried the microfiber one yet, but the foam bonnet did a great job on my finish! I have a 2000 Pontiac Bonneville and couldn't be more pleased with how it turned out :-). Only complaint I have is that I had to use almost all of the pads in one waxing session - not sure if the washer will take the wax outta the terry pads or not

This is justbwhatbi was looking for to wax my 19' sailboat. Pads for wax application, removal, and buffing. Easy on and easy off my buffer, but they stay on. Much better than the pads that came eith my buffer. I love the microfiber buffing pad. It really works great. The price for this set is similar to what I have seen for a single buffing pad.

This was the first time i had used my buffer wheel.I had this wheel for 4 years and was kind of skeptical about using it because I see other cars that had been wheeled and they have deep swirl marks in the paint after someone had completed the wax.From seeing these type of wax jobs I thought the buffer wheel was taboo .But once the pads were delivered I had a little confidence in myself and I am so glad I had ordered the pads.I have a 2002 Cadillac Deville DTS painted white diamond and the results were professional.The wheel and wax combination brought back the deep sheen in the color and made the body panels as smooth and slippery as a wet road in minus 32 degree weather going down hill.Thank you for the pads and the great price.