VersaTex Garage Floor 18 x 18 inch Square Rubber Diamond Plate Interlocking Floor Tiles for Home Gym, Garage Flooring, Trade Show Flooring, Basement Tiles, 8 Pack (Black)

I used 5 boxes in a basement workshop / furnace room / storage room. I had 1' square VCP tiles I installed 20+ years ago but the glue became brittle and the tiles were popping up. I liked that material but they run over $2/sft, are brittle, and are a lot of work to install so I looked into many, many flooring options. I went with this product and think it was the right move for my situation: - Interior basement floor, will never see sun and the temp is nearly constant - Can be removed / recut if needed to accommodate a different furnace, water heater, or big shelf that I want to anchor - Looks decent and cleans/sweeps easily - ships/sold by Amazon proper (better faith if returns needed) - made in the USA from recycled rubber I didn't follow the install directions literally, I started at the edge you encounter when walking in since I wanted that to set the line and look for the rest of the layout. Along the front edge I trimmed the little tabs off for a clean look, but didn't along the left and right walls which fit perfectly without any trimming (luck). The back wall and around a few obstacles I had to cut tile - it's only 4mm thick but like cutting through a hockey puck. You can't just score and snap these like drywall, you need to cut through them. I tried utility knife with drywall square (requires perfect alignment from cuts on both sides), angle grinder (just no), and had the best results with small tin snips. The right combination of sharp and leverage (helped to wear gloves). Other random thoughts: I don't think these would be good in a garage that gets sun or used for parking cars, especially where it snows. Water/salt will get under and it's not a quick task to take them apart. Maybe once a year pulling the floor out in big sheets to do a cleaning but seems like a lot of work. My garage is epoxy (Rust Bullet) which is a pain to install but no worries on expansion, water trapped, shoving tiles, etc. These tiles in an interior room or utility shed I think is the ideal use, just have options on how to cut them and be realistic on your expectations with this very low cost flooring solution.

I installed these on my garage floor. They snap together easily although using a rubber mallet makes it even easier. The tiles are dense, hard rubber and appear to be good quality. I originally planned to cut them to fit along the walls using a utility knife. This might have worked but, due to the denseness of the material, probably would have been difficult. I cut them using a portable table saw and, if possible, I recommend you cut them that way. Good clean cuts and much easier.

Looks amazing. Super simple and quick to install. Water can get underneath but seems to dry fast if you leave the garage open. It does curl/warp under direct sunlight, but seems to go back to position when not in sunlight anymore.

These were perfect for the garage gym.

Product installs well and seems durable material. As others have said, the issue is that the tiles don’t stay together. They literally separate at every single joint with any temperature variance. I even used double sided tape to hold them in place at each intersection but that only lasted a few weeks. I haven’t measured but I would guess that the tiles have lift up 2-3 inches at almost every intersection. These are absolutely junk. Do not waste time or money.

The pieces snap together easily, lay flat, and are easy to move or reposition. I made pads for the car tires by fastening 2 pieces together.

Used for my workshop is had to add rubber side trim to make it look good but it was worth it.

Fits well together. Garage floor looks like new. Buying my husband one or two packs at a time. Makes a great gift for guy who asks for nothing. Durable easy to clean. Got the dark grey looks very professional

Easy to fix

Great quality. Very heavy duty.

Pour avoir un anti dérapage sur une porte de trailer.

Bought these tiles to cover the plywood floor in our potting shed. These are well made rubber tiles for their thickness. A bit tough to cut. Utility knife and straight edge made cutting easier. The tabs really lock each tile in place. Using a mallet or banging them in with your hand.makes installation easy .Seamless looking floor. Easy to sweep and wash.