CableCreation Cat6 RJ45 Connectors, 100-PACK Cat6 RJ45 Ends, Ethernet Cable Crimp Connectors UTP Network Plug for Solid Wire and Standard Cable, Transparent

This review is for the CAT6A connectors. I recently ran out of connectors in the middle of adding a couple 24 port switches to my home network. There are lots of garbage connectors out there. Lots of pass thru connectors but I’ve never liked them and if you care about connection speed they aren’t an option. After a couple hours of research these seemed like the best bet. Turns out I made a good choice. These are great connectors. I have not had any issues with them whatsoever. Some reviews mentioned the tabs not locking. I did a pull test on the patch panel and one of the switches and the stayed in place. The patch panel and the RJ45 port on the switch flexed but the connector stayed connected. I have to assume the complaint was a different model connector or a bad batch. I didn’t hear a ‘click’ but some connectors don’t ’click’. I use 23AWG CAT6 and they crimped well and they held the cable in place securely. I suspect the reviews complaining about the connectors not holding the cable securely and crimping issues were from people using CAT5 and possibly a low quality crimp tool. I checked a few cables with iperf and was able to get 2.39gb over 2.5g ports. One thing to note is that since there is no metal shield for the connector they aren’t really CAT6A connectors. They work as expected and the price was right. I’d buy them again.

These are the best and easiest ethernet connectors I have used. They work great with Klein tools and have let the full speed of CAT6 cable through in my tests up to my longest test at 100FT.

Most end users this may not apply to, but to the extreme user this may. I terminated mutltiple drops in a channel config (tip to tip connectors), and a few with tips on the station side and a quality patch panel on the distribution side. These were attached to commscope cat 6 plenum rated wire. Each of these drops (cables) were tested using a Fluke Networks Lvl III Cable Analyzer. Using the industry standard of near end cross talk (next) as a point of measurement for termination quality these tested quite well. The lowest I got was 11.8 db margin with most in the range of 17-18 db. These mod tips perform quite well. Should be noted a few had to be redone to achieve these numbers, but this is a installer issue. Stepped on a few and beat on a few to see if they would shatter or deform easily. These mod tips didn't even skip a heartbeat. Pros: Exceptional value for price. Test and perform exceptionally well. Resealable pack that can survive a tool bag. Gold plated conductors. Proper dimensions, no sloppy fit to jack. Cons: I call it snap plastic that everyone uses to make mod tips. This causes the clips to break off very easily. Note, I did NOT have any that did. But after crimping I had to pull the clip backwards to give it memory again. Each time worried the clip would snap off. Each cable was done with a strain boot to protect the termination. This is NOT per se a bad mark on the manufacturer, just a general market item. There are a few out there that use a significantly different plastic formula. But these are rare and hard to find. Note, I rate all mod tips that do not have enhanced clips the same, but again these are rare and hard to find. It is just a honest opinion. The "snap" plastic is the industry standard, and in no way should reflect this brand name or manufacturer.

First, I ordered this type by mistake(non-pass through). Second, they are pretty good comparatively. I have not had any failures at this point and have used about 25 of the 100 I ordered, Normally I have 2-3 out of 50 that are messed up inside the plastic and need to be discarded. So far so good. The one problem I have is that the connecting face has a small wall of plastic that needs to be cut away on about half of these. If you know to watch out for it, it is not a big deal(most brands have this in some small way). If I wanted non-pass through for some reason I would order these again. Decent quality at a decent price.

I tried Pass Through connectors and did not like the exposed bare wires. I will go with these.

By far the easiest and best quality ends I've used. Gone are the days of the 2-piece and frustrating alignment slots. Get your wires reasonably straight and flat and the connector does the rest. Very impressed, using these from here out.

High quality RJ45 ends that is easy to crimp, provide sufficient space to insert the tiny wires, It's also strong plastic and the locking mechanism/clip doesn't break, I recommend this if you want this style of RJ45 Connector

Comes in a lovely packet, they are A class quality. Just made some cables, for the virgin media box and ps5 super fast, thought it would max out at 100mb but went upto 500 plus (max net speed i have)

Good but not through connectors

ممتازة

Great quality.