Hardline Products Series 200 Factory Matched 3-Inch Boat & PWC Registration Number Kit, Red/Purple,REPUG200

I decided to replace the registration numbers on my boat. These looked like a good product so I ordered them. They come nicely packed in a clam shell package. They are 3 inches tall. The vinyl itself is on the "thin" side - I thought they would have come a bit thicker. On some of the numbers/letters I needed to use, I had a hard time removing them from the backing because the backing was cut when the letters/numbers were cut. On some other numbers/letters, the vinyl wasn't cut all the way, so I had to pull a bit to get them to separate. Due to the "thinness" of the vinyl, I was afraid that I would stretch or distort them. Luckily I didn't or I don't think I did. The product was easy to apply. They look good on the boat. I gave them 4 stars due to the issues with the cutting and thinness of the product.

the vinyl is thick and sticks really well without bubbles. it was a fairly easy job to put the letters on, just have to do a lot of prep work, this is what I did:scrape old letters with razor blade + acetone to get all the old glue off (take extra care not to scrape off your registration stickers or other permit stickers that may still be valid like I did!! DOH!!)get a roll of painters blue tape, make a long double strip with sticky side updo not peel letters, but cut the ones you need out with scissors and peel the OUTSIDE part, not the letter itselfwhat you end up with is a bunch of squares with the vinyl letters still attachednow stick the squares to the tape white side down so you're looking at the lettersI did this freehand since you can use the squares as guideswhen you have the letters attached, make another double strip of tape and this time attachthe tape sticky side to the letters themselvesmake sure the surface you're attaching to is clean and dry, now peel back the tape from the white/rear side to expose the glue on the letters. it will come off very easily leaving just the letters attached to the tapeclean boat surface with alcohol to remove residuenow apply the letters to the boat and spend some time rubbing on the tape and letters to make sure letters stick to boatnow carefully peel off the tape from the surface, after that you can use a rag to rub the letters some more to make sure you get any bubbles outdon't use a credit card or anything hard, you'll scrape off the protective finish and mess up the smooth vinyl surface

Great lettering kit, my last one of these lasted 15 years on a jet ski!! Pretty amazing they lasted so long - the stickers were actually fine, they just finally got torn up brushing up against one two many docs. BE CAREFUL in checking your letters/numbers for duplicates since you only get 4 of each character. In my case, I had three of the same numbers needed (times 2 sides of the vessel) - so had to buy a second pack and wait for those to arrive.

Had good success on the first watercraft we put them on so we went to ordered a set for the second watercraft. The other digits stuck however all four of the 9’s and U’s didn’t seem to have the same adhesion quality and all of them fell off, making the numbers that did stick irrelevant. I will be contacting the company and updating this with what they decide to do to make it right.UPDATE: I sent a message to the company and they responded very quickly. They sent me replacement decals, which were of noticeably better quality, and they have worked great since. Excellent product and even better customer service!

I bought the product to put a registration number on my kayak. 2-3 hours after putting it on, I went bak to kayak to find out the stickers were already peeling. I don't think the adhesive on the stickers are meant to be for plastic kayaks (polyethylene). I like the letter design. It looks really nice right after I put the stickers on. A little disappointed. ....

High quality decals with multiples of each number and letters. Super sticky adhesive. I stuck some of off cuts to my dirty old winch line (which is seatbelt material) and they are still there after being used and dunked in saltwater. If it sticks to cloth like that you know they won't come off your boat. If you prep it properly. I would recommend I quick clean with window cleaner and then a good clean with wax and grease and remover and you'll never have to issue

I had a set of these on my jet ski, lasted for years. Replacing them was easy, just use WD40. Nice looking and the individual letters (instead of the blocks like the popular kind) make it easier to align and look good.

Very upset. We have been waiting for these letters to arrive . As soon as we opened the package from amazon which was plastic we could see the other plastic packed for the letters was damaged. It looks as thou someone either used these letters and returned them or the packed got wet. The stickers are stuck to the packaging. The letters have white stuff stuck to the black and red and some of the numbers can’t even be removed from the package. Wasted time and money

Plenty of letters and numbers probably could do 2 boats. Priced below most I have seen. Appears to be good quality.

Good look but doesn't stick well on inflatable boat. Didn't last 2 months. Luckily there's plenty of spare numbers so I can replace the lost one.

Utilisés sur un ponton. Bonne grosseur et colle très bien. Correspond à la description du vendeur. 👍Reçu le produit à la date prévue.

Much brighter scarlet red than appears in pics. I was looking for a darker red to match my boat.

Love them on my boat