RV Designer 1 Inch Wide Vinyl Trim Insert for RVs - Flexible Molding, Exterior Use, and Roof Edge Molding - Ideal for Travel Trailers and Campers, Heavy Duty, 100 Foot Roll, Black

I picked this up to swap out some damaged trim on my camper and it turned out great. I measured the old piece to make sure the fit was right, ordered it online, and had it installed quickly. Based on what others suggested, I left it out in the sun beforehand to soften it up a bit, which made the process even easier. The whole job took about ten minutes from start to finish. The material feels sturdy and has a clean, polished look that matches the original trim. The seal was snug but went on without a struggle. For the cost, it’s a solid value and definitely worth it.

this worked out great after purchasing two other products that did not fit properly. Very easy to install, looks good, nice and thick. I’m confident it will last for years..

easy to install for repair of deteriorated strips on my RV

DATE ORDERED: 03/12/24 DATE ARRIVED: 03/15/24 DATE OF REVIEW: 03/16/24 PERSONAL BUY / PRODUCT TO REVIEW: Personal Buy DELIVERY: Arrived by UPS. Good Packaging. QUALITY: Thick Rubber Trim Molding. Advertised as 1". Actual dimension of product received was closer to 7/8". INTENDED PURPOSE: 5th Wheel RV Gutter Trim RECOMMENDATION: We have a 5th wheel. Its an older model that came with the standard plastic trim. It has fallen apart after 10 years. Brittle; Cracked; Split; Faded; Falling out of the track. Thought we would try rubber this time. On initial inspection, I was concerned because it stated is was 1" trim. Actual measurement was closer to 7/8". The rubber seems to be a decent quality. It is a bit stiff and will wear your fingers out as you install it. Each side run on our RV is 40'. Times two, I needed 80'. Taking the old trim out was easy. It was brittle and cracked anyway. No sense in being gentle with it. After removing the old trim, it took about 1 hour per side to change working from an extension ladder. The new rubber molding is stiff. It looks great. We purchased the black trim. It 'looks' like it will definitely outlast the previous molding. I/we would recommend that when you need to replace your gutter trim molding, this is a great alternative and very cost effective. Be patient while you're installing. Insert into the bottom track first. Work about 4" at a time. Do your best to fold it as you go. Clean the track with a small vinyl brush first or as you go. Verify that you have it inserted fully into the track. You don't want to have to pull it back out. This is not a hard job. Almost anyone could do it. One suggestion...Do this on a relatively warm day (I did ours when it was about 50 degrees F. and sunny. I unrolled the rubber out ahead of time to let the sun warm it up. That made it a bit easier to work with). At this point, I would buy this product again should I need more. OVERALL RATING: 4 Stars. I would give it 5 stars but need time to see how it does in the heat and cold for expansion and contraction properties. We need to make sure it stays in the track. Installed on 03/15/24. Will report back at a later date.

This product is amazing. It has a slightly thicker and rubber like feel the fits snugly and looks great. Our original trim was painted with the RV and I was afraid this wouldn’t look good but it looks better. Just make sure to buy black caulk for the securing screws at the ends. The original trim was coming out of the track constantly at the end of 2024 on a 2021 model. This stuff has been on the RV for over a month and after a road trip it’s perfect! Buy this and stop looking any further.

Soft & flexible. Fit perfect! Easy install

It was time to replace our insert molding on our 2019 Grand Design 337. We're full-time and are exposed to every type of weather out there. When inspecting the insert it was getting noticeably harder and less pliable. The replacement was straightforward and it is a good idea to let it warm in the sun for a bit to add to the flexibility. Taking out the old insert was easy and spent time inspecting the insert grooves, cleaning them out with mineral spirits and a small plastic scraper then securing the screws and using some Lexel sealant on the screw heads. Just make sure the insert sits securely in the insert grooves as there may be an area or 5 or 6 where it may not catch properly. I also did a beed of Lexel about 3' up from each end to further prevent moisture from getting in and securing it so as to avoid the dreaded insert molding flying around down the road scenario. Also, consider a few short areas over the length of the insert strip where you put some additional sealant just in case. When it is time to remove it again, it's easy to pull it right out sealant or no sealant.

Great, easy to install

The RV Designer E569, Heavy Duty Vinyl Insert is an excellent choice for anyone looking to replace or upgrade their RV's trim molding. This vinyl insert offers durability, flexibility, and ease of use, making it a valuable addition to any RV. Design: The insert is made from high-quality vinyl, ensuring it is resistant to wear and tear. The 1-inch width fits standard molding, and the 50-foot length provides ample coverage for most RVs. The black color adds a sleek and modern look to the trim. Functionality: The heavy-duty vinyl insert is designed to protect screws and prevent leaks, making it an essential component for maintaining the integrity of your RV's exterior. The durable material is also flexible, allowing for easy installation and adjustment. Durability: The vinyl insert is built to last, withstanding various weather conditions without deteriorating. It provides a long-lasting solution for cracked or stained trim, ensuring your RV looks its best for years to come. Ease of Use: Installing the RV Designer E569 is straightforward. Simply measure and cut the vinyl insert to the desired length, and press it into place along the trim molding. The flexible nature of the vinyl makes it easy to work with, even for those with little DIY experience.

متاز جدا نفس مقاس الوكاله.

Arrived in a couple days, very heavy duty and flexible rubber like substance," not plastic". Went on with ease and looks great. Time will tell on longevity. Doing the 90 degree bends on the back of unit were a bit of a struggle do to thickness, but with a little patience I got it inserted. This is now my go to insert trim brand.

was able to replace the split and plastic one on my cargo trailer. These are more rubbery not plastic and were easily installed The industry standard is 1 inch so fit my trailer exactly. 50 feet was more than I needed but if my trailer is still here in 20 years i will have enough for that

Great product, easy to install