PC Products PC-Clear Epoxy Adhesive Liquid, 16oz in Two Bottles, Clear 70161

The product works well. No surprises. . The stopper or lid/cap that holds the liquid mixtures in is well designed and comes on and off easily. You don’t have to cut the tips and deal with annoying snap-on caps/lids. The lid/cap simply twists on and off. I’ve used the product four times already removing and putting back the lid/cap. No mess and the cap/lid works and comes on and off without issues. . The plunger is smooth and trouble free. . The two liquids come out clear and transparent, but turn slightly opaque when mixed. The epoxy mixes into a liquid consistency similar to chocolate syrup rather than tomato catsup, so viscosity is not that thick, so it will run. I recommend using a tray to mix. I used a piece of cardboard and experienced some running. . When applying, note that the epoxy is lesser in terms of viscosity. It will run off your scraper and spill, so take care. But spillage is easy to clean with a wet paper towel. . Don’t over-apply. Just make sure you can get even costing on both aurfaces/sides of the materials to be bonded. . No nasty odors. . A couple of minutes after application, the epoxy feels sticky and rubbery, but that goes away and the material will turn rock hard after an hour or so. Epoxy dries clear. Hardly noticeable even after applied on a wooden door that is painted white. . Very good bonding. I used masking tape to clamp/hold the glued pieces together. And the tape came off easily after curing/hardening. . I would most definitely buy this product again.

At first I was hesitant, but after use was extremely pleased. The three cartridges were good and gun worked great. The partially used cartridge could be recapped but nozzle were not reusable understandably. I was able to seal every rivet and seam on the bottom of my 14ft aluminum rowboat with clear dried epoxy.

This stuff works great, but you should practice with a small amount prior to use. The cure time is good for very small applications when used by someone with a bit of experience. If you rarely use epoxy, are working with above room temperature materials or environment, and/or have a large project that you can't do with small batches then pass on this. The work time is far too short for anything outside of those parameters. You'll end up wasting your epoxy, money, and time. This is ideally used in very small volumes (0.25 fl oz. of each part maximum in my opinion) unless you're experienced. I'm not saying it's impossible to do more, but I wouldn't recommend it. 4 minutes of work time might sound like a lot, but it's really not. It's really important consider those factors I mentioned. This is good stuff if you use it correctly.

Used this epoxy as a finish top layer to cover a long (the >3 feet long) granite bench >1/4 inch-wide crack filled with strong adhesive glue and colored to match the granite. The gap of the long crack could not be clamped to be narrower without completely breaking the 2 -3 inch-wide long edge of the bench into many pieces. Plus there was a partially deteriorated supporting metal plank upon which the granite bench was glued, so the two pieces were hopelessly separated. Estimate prices to repair or replace the granite bench was ridiculously too expensive. So I used ChatGPT4.0 to come up with solution: First I cleaned out the gap with brush and vacuum. Then filled the length of crack with strong adhesive glue (LOCTITE PL Premium 10 oz. Polyurethane Construction Adhesive) from above and later from underneath where rust had deteriorated some of the metal support. I filled it just slightly below the surface level. I trimmed with a razor blade if it cured higher than surface level. Then I colored the visible tan colored glue with markers and acrylic paint to match granite colors and pattern. Finally, I applied this epoxy layer to protect the colors and pattern from water and make the repair flush with the surface of the rest of the bench. The epoxy was somewhat self-leveling, but can shave excess edges with razor as needed. Not bad for a DIY in an area not readily seen by visitors. Hope the epoxy can withstand the humidity and water exposure as the product claims it should.

If used properly, this stuff makes an incredibly strong bond. I used it to attach a copper pipe to an aluminum pipe on a DIY project. I realized that I needed to make changes and get the copper pipe off. Nope I broke the copper before I could get it to budge, Which I then had to hack saw it up and break parts off with pliers to get the copper off so I can re do it. As an adhesive, thats pretty much a 10/10. My intent was ot make my 2 pipes one, and this did that pretty perfectly. If you use this wrong the bond wont be great, but used well its amazing. Bonding 2 flat surfaces together isnt nearly as good. If you rough the surfaces up it helps, but all it needs is for one edge to cope up a tiny bit and it can be popped off. But if its a 3 dimensional joint, so that theres adhesive stopping it from moving being able to pull off, its amazing. When properly used, everything I try to take off breaks before the epoxy goes. So as a permanent solution I couldn't ask for more. And for ease of use, its very easy to use. I just squeeze a bit onto a piece of cardboard with packing tape on it to make a water resistant surface. Mix them with a paper clip. Apply it. Wait. Note that a hot environment will set faster. Try not to get it on your hands, its sticky and doesnt come off well, even with dish soap. But its not like super glue so it wont just instantly stick your skin together. so it gets points over glue for that. Also this is incredibly cheap and non toxic when cured. Meaning it should be safe for most applications. I cant really ask for more.

Excelente epóxico, de verdad que sí pega el cristal, ya lo utilice en el cristal de mi comedor y de verdad que sí resiste..

Sent without packet - only the syringes were delivered wrapped in a plain plastic wrapper. No instructions for use were received.

اشتريت باقي التجربة ان شاء الله ممتاز

Muy buena aunque es muy poco precisa. Huele muy mal pero supongo que es por la resina.

This stuff is great! I bought it purposely to repair the lid of an old ceramic sugar bowl, of purely sentimental value. I already had superglue, which would probably have worked but does not give a very strong bond. I have used epoxy adhesives in the past for ceramic repair and often been disappointed by the poor fit of fragments and the yellowish lines of the adhesive that remains clearly visible between them. The simple dual-syringe mechanism works perfectly, as does the re-sealable cap. Working time is sufficient to mix the product, apply with due care to two surfaces and to press the pieces into position until they are fairly firmly fixed. It's worth noting that you also have a short time to wipe away any excess adhesive - definitely do this before it sets! I left the repair to cure fully overnight and the result is perfect - the join is almost entirely invisible.