Williams SCF52 Crowfoot Wrench Flare Nut, 1-5/8-Inch

JH Williams SCF40 Crowfoot Wrench Flare Nut, 1-1/4-InchI have been a wrench bending grease slapper for over 35 years and I have used and abused many tools in my time. Crowfoot Wrenches really take a beating as they are specialty tools to get into places that one could never get to any in any other manner whatsoever. That being said, they tend to get a beating and spread with over use or excess applied force.Pros:This tool the JH Williams SCF40 Crowfoot Wrench Flare Nut, 1-1/4-Inch took some major abuse. I knew that I would ruin it but, the task I had to perform require 500+ pounds of force to break the part loose. The tool is well made, did not drop, did not break or off the extension and did the job that it was intend to execute.1.> Arrived fast.2.> Well made.3.> A very high quality tool.4.> Performed outstanding under horrific use and abuse.Cons:Please let me clarify that the nature of these types of tool and the abuse they receive in their use is not intended in any manner to reflect on the quality of this tool supplier or manufactures. There are no real CONS in my review because I understand, steel loads, types and the nature tool steel. There is a cost for everything in life and these get the job done at a very low cost. I do keep the old ones for pre-loosen nuts and hydraulic hose coupling and sometime you need two of these too.1.> All Crowfoots spread over time2.> They don't not last forever, so if you use them frequently as I do, then you need to have spares on hand or order multiple of the sizes you need to have on hand3.> 12 PT Crowfoots will slip when over driven; they will spread given the same conditions too.I gave this tool a 5 star rating because it did the job and saved me over $1000.00 USD. I will definitely buy more of these from Amazon and the Seller. I do highly recommend this tool and its seller. I will be using and testing others as my work on Heavy Industrial Equipment continues.

It's what I needed to get the job done. Will buy this brand tool again when I need another size. Very nice. Excellent quality!

Great for right spots using AN fittings.

Used for large to fix a loose hydraulic line in a Cat skidsteer. Had to trim part of it to get it on the fitting. Held up to enough torque to snug up the fitting. The machine is all metric and I'm not sure if those fittings are supposed to be 1-3/8 or 35mm , but 1-3/8 fit on the hex fine. 35mm would have been too big.

Will not break a nut that's torqued down and isn't strong enough to torque one to spec, it will flex and slip. The 12 point design was easier and a little faster once the nut was broke loose with another tool, especially in a tight spot.

I had to buy this tool to remove a ford EGR valve line nut. It takes a 1/2 drive breaker bar. Worked perfectly. Very high quality tool. Made the job a cinch! A+

This was just what I expected--and needed. The description, as others have stated, shows both 3/8" and 1/2" drive. By now this should have been corrected to indicate 1/2".

Had a hydraulic fitting on my skid steer that was not accessible with a wrench. This allowed me to remove and reinstall the new hydraulic line.

I am an aircraft maintenance engineer and I work on helicopters. I purchased this tool to reach a hard to reach area on one of the machines. The tool finish was excellent and the fit was also excellent. I felt the price was decent as well as I had compared it to snap on and other tool brands. I also appreciated that I was buying a quality tool made in North America.

A necessary tool for the removal of a hydralic pump on a Case Steiger tractor. Works well.

works as intended

Bought it to change the fork oil on my EG Ultra Classic. Worked OK for taking the caps off but when trying to torque them on install the crowfoot started to spread and round off the cap.