Pedaltrain Voodoo Lab Power Supply Mounting Bracket for Pedaltrain Pedalboards

Used these risers on a vertex tour pro to help clean up some cable routing. The little bit of elevation & flat surface work great to hide some wayward cabling. Bonus points for including appropriately sized screws AND velcro. Would buy again.

I have had a PedalTrain2 w/hard case for a few years, and two of my favorite pedals were always a little low on the back row. They are a TC Nova Delay and MAXON FL-9 Flanger, and while the TC just needed height, the FL-9 with the Ibanez type switch also needed to be leveled because it was tricky to push down on the actuator at the stock pedaltrain downward angle. These are not cheap pedals, and it was really a bummer that I would have to perform an annoying dance to activate them, and many times would inadvertently hit the knobs of other pedal. Well I just finished installing and testing the Large Pedal booster, and it fit those two pedals perfectly. I was concerned because the Nova delay is fairly wide, but no problem at all. The booster velcro'd in nicely, both pedals fit just fine, and immediately I could use them easier than if they were on the floor because of the added height and fact they are both now level (YES!!). It honestly feels like a new board because all my pedals are equally useable and I no longer have to worry about messing up other settings. And most importantly, my pedalboard still fits perfectly into the hardshell case. You will need to lengthen the connecting cables a bit because of the added distance, but the little bit of work is totally worth the return. All and all, the PedalBooster was well worth the money, and I only wish they had made it a few years back. Highly recommended if you have some pedals that need a little boost or leveling.

Works as advertised. Was worried it would stick up too high but it sits perfectly where you'd want it to for normal sized pedals.

Pedaltrain Model: PT-VDL-MK. I used these brackets with a Voodoo Lab Pedal Power 3 Plus and a Strich Plus 22 and they fit perfectly. The PP3+ original screws were fine to attach the brackets to the power supply and the Pedaltrain supplied screws worked great to attach the brackets to the board. No complaints, highly recommended.

Perfect for my pedaltrain classic jr. Only concern is the lack of openings for my Voodoo Plus 2 sides vents. So far so good, and other folks have said they haven't had any issues with over heating. However, that's to be tested at a long and hot venue site. Last but not least, the screws that came with it sucks. Try using different screws because two of them broke on me.

Great for organizing pedalboards into separate levels or as a small board for up to three pedals, I have a couple of these. While using one for quick setups with several amps, on a larger pedalboard I reversed the booster to raised the pedal bottoms by 1” over the lower row that impeded switching the top row.

Bought this to mount a voodoo labs mondo power supply to my pedaltrain pedalboard. Mounted up (gigitty) very well and it’s very sturdy so to answer two questions right off the bat “Does it work with a pedal train pedalboard?” -yes “Does it mount up to a voodoo labs mondo power supply?” -yes

Bought one of these last month to use as a small pedalboard on its own. I used the included velcro (which, if you let it cure the 24 hours it suggests, works very well) and just slapped some rubber feet on the bottom. Now, I have a small pedal board that fits three MXR-sized pedals (with patch cables) that I can take with me if I don't want or need my full-sized board. While there's no room for a power supply, I'm not disappointed at all. It's small, seems to be made of a sturdy type of metal (I'm guessing aluminum, like all the other Pedaltrains), comes with enough velcro, and most importantly, is only twenty bucks. If you want a small, inexpensive - but sturdy and attractive - pedalboard, just put some rubber feet on this, and I'm sure you'll be happy.

Too bloody expensive but it does the job well. I give it 3 stars only because of the price, not justified in my humble opinion.

Excelente artículo! Muy recomendable y la calidad es excepcional!!! Satisfecho 100% con el producto!

Perfect for PedalTrain Classic Jr. Very lightweight, but also sturdy. It fits perfectly alongside the triple version on a Classic Jr.

Originally thought this was an overpriced and pointless accessory. But, I decided to get one after I kept stepping on other pedals controls around my overdrive pedal. This item acts as a perfect adapter for raising the pedal to a better height. I was happily surprised to find that the riser can be fitted with either self tapping screws or with Velcro which allows me to move it around on the board when needed. Both the screws and the Velcro strips are included. I chose to Velcro the riser on to my board and it feels very secure and stable (I gently shook my board upside down to check it’s secure). I’m now considering adding a double width one to allow me to try a different layout for a bigger pedal.

These got the job done with a PT-2 (older version of classic 2). The pictures show these mounting an ISO 5. The PP digital would also work. I can't speak for any of the other voodoo psu models, there is a limit on the space it needs to fit in. Just bend one side of the tabs and drill new holes. A little expensive for 2 pieces of cheap metal (bent with my hands lol). They have the market cornered though, what can we do?