M.2 Heatsink SSD Cooler for PS5 PCIE NVME or SATA m2 2280 SSD Cooling（Black 2 Pieces）

I added some SSDs to my computer and I always add these too. Seems to keep the SSD cool and performing well. I have had a couple SSDs that slow to a crawl when transferring data to them like building an image or dropping large files. Once I added these, the performance was a lot better. PROS: It comes with everything you need. - Heat sink, nice pads, screws... I can recommend this product. - Assembles easy and give a place for the heat to go from the chips - Works with my Desktop PC motherboard and all the mini PCs I have. - Says it works with PS5, but I didn't test this. CONS: - Not really any quality instructions, so you have to figure out the placement on your own. it took a little testing trial and error to get a good position, but its not hard. Also know the layout of your device as I think maybe every device takes a little shifting to get a good fit. - May not fit well in all devices. they add a bit of bulk to the SSD and may cause the drive to not fit. so test and use a bit of trial and error.

I just built a new PC workstation, and while I was putting it all together I used these heatsinks for two of my NVMe M.2 drives. And... I was VERY PLEASANTLY SUPRISED by how nice of a kit this is and how well thought-out it is and all that for so little money. Nice job folks! This kit includes a little screwdriver which also has a magnetized tip that makes it much easier to work with the tiny screws, and speaking of the screws it not only includes all the screws you'll need to put the thing together but it also includes two extra screws (one for each heatsink unit) that you can use to latch down the end of the M.2 card to your motherboard because yeah you probably don't have one of those M.2 screws handy do you? Well no worries! And this includes four thermal pads (one for top and one for bottom of each of the two drive kits) which are of different thickness, so read the manual to make sure you use the right thickness thermal pad on the correct side of your M.2 drive - it's easy to visually tell them apart as one size is visually thicker. It also includes a legible and simple manual which was great as other wise I wouldn't have known which thermal pad to apply to the front and which the back. Finally it includes wipes (wet and dry) to clean off your drive if you need it. Such a well thought-out little product. What a value! And it also looks great and WORKS great too - my drive temps have stayed nice and cool.

Low cost product, easy installation, performs better than expected, about the same as a factory-installed heatsink on an NVME SSD that is directly adjacent (on the same PCIe expansion card) to a pair of NVME drives with these heatsinks. Per hwinfo64, at idle: PCIe NVMe with factory heatsink temp: 32c PCIe NVMe with this heatsink: 30c Motherboard NVMe: 42c

Simply due to the physics of it, these units are slightly larger than the average heat sink. However, they are vastly more secure and very efficient. Rubber bands break, screws don't. Metal housings don't. I've installed these in two mini-PCs and they fit well. One of the two is a bit tight since the mini-PC is not only small footprint but also small in thickness. However, everything still fits and the heat dissipation works better than the previous one-sided heat sink that already snapped a rubber band after three months of use.

I was skeptical at first with these due to the provision of thermal pads and not thermal paste but once I received them and felt the quality of the metal and saw the profile, I was pretty sure that I had a winner. These have a low enough profile that expansion / GPU cards, safely sit over them without issue. The deep channels and openness of them, allow for adequate flow of air and removal of heat from the SSDs. The instructions were OK and my recommendation is to squeeze down the heatsink as tight as you can to ensure that the pads are touching all surfaces without air gaps. The adhesive was good for the initial lay down and didn't set up too quickly and allowed me a few attempts to put the thermal pads on straight. After booting up the system and copying over 4TB of information I found that the drives ran A LOT cooler with these in place by both touch and through Samsung's Magician app. Heat is the enemy of electronics and this is just what I needed.

Easy to use and gives peace of mind and cooler temps.

With the thermal pad properly seated it is keeping the temperature right around 40 degrees C. I'm using a gen 3 computer and the speed of the nvme is around 3000Mbps. This is with family movie video transfers and converting from mpg to h264. It has slots that allow the height to be adjusted to properly seat the thermal pad. After adjusting the height just tighten the screws. It mounted on my motherboard just fine.

Works good keeping my NVME drives cool. I had flat ones originally from my motherboard manufacture but the fins dissipate heat better .

Not tested yet, but it's built quality looks great. Should be better than those heat sinks that are held together with rubber bands.