Bora 24" NGX Clamp Edge 544024,White

I got this with the saw guide, to make an "affordable track saw".Works pretty darn well for that purpose, once you get the edge guidealigned with your saw.BIG TIP:The clamp always seemed to be "sticking". Sometimes it would slide easily, butoften it would jam up and stop sliding at all. It took forever to figure out the trick.Now it slides easily all the time. The trick is this:* The orange part of the clamp has two little tabs sticking out at the back end.* I had no idea what they were for, and none of the instructions mentioned them.* You put the heel of you palm against the back of the gray handle (in the "open"position), and then pull back on those tabs with your fingers, as though pullingon a hypodermic needle.* Voila! The internals of the clamping mechanism (whatever they are) COMPLETELYdisengage, and the clamp slides freely in its track.Important Notes:1) In the pictures, the "edge guide" looks like thin tape that could go anywhere.It's not. It's a nice, thick piece of plastic, with adhesive on one edge so it is ready toapply, and there is cut-away on the bottom of the clamp to attach it to, so it works well.2) You NEED the edge guide. If you use the clamp for cutting sheet goods, you darnwell want that edge guide in place. It is the ONLY good way to align the clamp forcutting. (There are blade-markers on the saw guide, but they're not really useful forlining up the cut when the saw is on the guide. (If you take the saw off, they may work.I didn't.)3) To attach the edge guide, it's best to remove the clamping mechanism. (Easily doneby taking out two screws. The instructions don't say that (they could use improving),but it's pretty easy to figure out there is no way to attach the edge guide the fulllength of the clamp, until you do.4. The tape on the edge guide doesn't QUITE go to the end. It's maybe 1/4" short, butthere is an inch of extra tape, so do yourself a favor and cut off the end of the guidewhere there is no adhesive, before you start applying it to the clamp. That will removethe slight tendency of the edge to lift up--something I may have to trim off, eventually.5. Don't bother with the T-Square attachment! Total waste of money, if you're using theclamp as a track-saw. (For details, see my review of that attachment. It works fine whenit makes a "T", but it has to be in an "L" configuration to work with your saw. And in thatconfiguration, it fails miserably.)6. Now that you know you CAN'T depend on the T-Square for alignment, and you MUST havethe edge guide in place, do yourself a favor and mark BOTH sides of the panel you're cutting.Then put the clamp in place, and cut away. You'll save yourself the half-panel I ruinedbefore I figured out those steps.7. But there is still ONE MORE PROBLEM to solve, if your saw is like mine.The edge guard projects 1/2" beyond the edge of the clamp.The instructions for mounting the saw to the saw plate don't SAY to put the bladeas close as possible to the edge of the plate, but they should.What they DO say is to make sure the blade guard is free to move.That's a darn good idea. BUT...On my Ryobi saw, "reasonably close" puts the blade 3/4" from the plate.The blade guard is pretty thick where it is close to the plate, so I can get itthe saw MAYBE 1/8" closer, while still being able to move the guard.I KNOW I can move it 1/16" of inch closer. And I MAY be able to move it 1/8".But I NEED it to be a full 1/4" closer, for the edge-guide to be of any use.In "short" (pun intended), the edge-guide is 1/4" too short for use with myRyobi circular saw. Will it work with other saws? Don't know. But I wouldcheck the width of yours. If your blade guard is more than 1/8" from theedge of the blade, it won't work.There is a WORKAROUND, though. So check your saw before installingthe plastic strip that comes with the clamp. If it won't be wide enough,double-sided carpet tape and a strip of linoleum are the perfect size.Here's the procedure:a) Get a linoleum remnant from your nearest big box store, along withdouble-sided carpet tape.b) Cut a 2" strip of linoleum the length of your clamp.c) Put double-sided carpet tape in the groove under the clamp.d) Turn the clamp right-side-up and use your razor-knife to trim the excess tape.e) Turn the clamp over again, peel the backing from the tape, and put down thestrip of linoleum, shiny-side pressing into the tape.f) Find a nice long piece of wood you can cut the end off, and do it.Voila! You now have a perfectly-trimmed edge guide!

Great quality LONG straight edge for a reasonable price

The connecting screws on this guide if you remove them often Suck! Very soft heads and strip easily. Suggest better screws. No where to find the size, so i finally figured them out. On my purchased guide; they are M4x6M Pan Heads. I bought a bag of 100 very hard 12.9 screws off Amazon for $9.00. Here is the description of the ones i ordered if interested - iexcell 100 Pcs M4 x 6mm Thread Pitch 0.7 mm Alloy Steel 12.9 Grade Hex Socket Button Head Cap Screws Bolts Kit, Black Oxide Finish. Note you may possibly need to use a drill press to slightly open gap over screw locations to fit these screw heads in through the track groove comfortably if you remove them often as i do for these screws. Best of luck, it works as designed but bit expensive for a soft aluminum track w/plastic parts. Extensive heavy use might not last as long as you may expect it to especially in cold environments. BORA needs to make entire clamping system from cast aluminum or better is my suggestion.

When combined with the Bora NGX saw plate (for mounting a circular saw) this becomes a viable alternative to a high end track saw, but at a relatively low price. A good track saw is more accurate, but they can cost 8 times as much.I recently used this (with the addition of a NGX saw plate) to cut full plywood sheets for a Murphy bed project and the results were great. Much better than my old method of clamping a straight board the full length of the plywood and running the circular saw along the edge. That said, be aware that the clamp is narrow, so when used at full length it tends to inflect slightly in the middle if you are not very careful and this can affect cut accuracy. Also, tear out on plywood is still an issue, particularly when cutting against the top ply’s grain.If you are cutting 8’x4’ plywood frequently and need high quality cuts, invest in a track saw. However, if you do this only occasionally, then the Bora NGX system is a nice alternative and you will probably be happy you saved several hundreds of dollars that you can use for other tools you may also need.

Nicely designed and enables flawless cuts up to the length of a full sheet of plywood.

Me encanto

I was hoping this would be a good alternative to a rail or track saw. I was quickly disappointed when I attached the extension piece. It was bowed up to a 1/16”. It really does no good to have a bowed straight edge. If they want to improve their product, I would recommend a wider rail and better quality control.

I have wanted something like this for years. It's a pain using C clamps and a board as a guide. Nothing works as well as you want and the clamps are finicky when trying to be precise. I recently purchased a small circular saw for cutting large format (2 x 4) tile. Clamping a straightedge to the tile just adds pressure for chipout. This works flawlessly, and if not abused will last me many jobs. When I consider that 2 tiles cost more than this tool I say this is the deal of the century. I made a flat tile holder out of 4 x 4s. Being planed dead flat tiles don't tend to crack near the end. The V groove is access for the blade and the off center cross member is for smaller tiles.Update. I was wrong. Tile dust got in the plastic clamping mechanism and locked it up solid. Only took a couple cuts. It's also thick to the point that I have to raise the circular saw up an that only leaves 1/8 inch below the tile. So ..... for wood it would probably be great not for tile.

As described

good Quality

Son más grandes de lo esperado lo cual es excelente. Llegó en buenas condiciones.

Exactly what was needed, really helped make the job easy when cutting down large sheets of MDF for a cupboard project. Great quality, nice and sturdy and the grips hold well with no slipping or issues. Would recommend.

Perfect for cutting full sheets of plywood. Breaks down for convenient storage. Recommended.