NMAZA 10Ton Hydraulic Gear Puller Wheel Bearing Pulling Separator 3 in 1 Pump Oil Tube Drawing Machine M/Case

I was going to video me the other night using this puller on a sprocket from a drive end/exit end conveyor in a car wash, but I guess I missed hitting the “red record” button and there was nothing. It would have been a very short video I can tell you that. In fact, it took more time, I’d say three times longer, to assemble the puller then it did to pull that sprocket off the hydraulic motor shaft. It was friggin’ AMAZING! No more hitting it with a sledge hammer to jar it a little loose before starting or even better, no more cranking your 1/2” drive ratchet over and over and over until it finally grabs and pulls it, if it ever does. This puller has performed outstanding on removing sprockets and bearings that for one are hard enough to remove from anything after a long while, but in a car wash environment, where water, dirt, slime and sludge are a constant,.....it Kicks A** !!! All that said, the parts in the puller could have been made more better and specific to this tool, like the bolts and nuts that hold the puller arms (they tend to tighten up or loosen up as your using the tool), or the really flimsy case it comes in (it won’t last a year for me). Those are they only issues I have with this puller and the fact that it does the job so well, I almost didn’t mention them. Love this puller.

I pulled off the driver side wheel hub assembly and it was the most difficult job I've faced so far. I had to replace the cv axle, wheel hub and ball joint with pretty food damage to the steering knuckle just to get the hub detached. I rented a puller at oriellys and that was pointless, I purchased an air hammer that was also pointless. This thing took several hours of hitting with a sledgehammer, torching and cutting and was a complete nightmare. So after a week I decided to give the passenger side a try but didn't want to experience that again so I looked around and stumbled on this hydraulic press. This thing is an absolute beast, I know it probably wasn't the same difficulty as the drivers side but this was off in just a few pumps with this press. This saved me so much time and energy and would highly recommend this to anyone. The assembly is a little unclear on the instructions but it's not to hard to figure out. It is pretty heavy so balance and lock on the hub do extra hands helps a lot. But let me tell you again, this thing is well worth the money spent on it, especially if you have to do more than one. I can't wait to replace the rear ones just to use this again! If you are on the fence, just pull the trigger and get this bad boy!

Great product very powerful it is a little difficult to operate it in some situation of one person it is best to have someone to help you to position the Pooler but I have stubborn seas rotors and this thing puppet release in 10 seconds amazing quality is decent you have to be gentle with it this is not the product that you be rough with it and handle it roughly you take care of it you shouldn't have any problem very powerful overall I am very satisfied with my purchase and I do recommend it especially for DIY mechanic you must have one.

It's a nice product, it works, but you need to know how to use it well and professionalism is required. You need to be good at using 3 hook legs and if you do it well, it will work.

My stuck flywheel destroyed 3 other pullers. Stripped threads and broken bolts littered my garage floor. Got this earlier today and rigged it up in little time. It took a couple of tries and a bit of heat from my torch but it popped the flywheel that I thought was beyond hope. This thing is heavy and a little bulky for mounting upright. However, the 3 jaws never slipped and the hydraulic press just kept the pressure on to defeat this monster of a problem. Worth the money even if it gets used only a couple of times each year.

I purchased this tool to help me remove a front CV shaft on my Ford Escape. Without the tool, the shaft wouldn’t budge out of the hub. I spent hours trying to get it out and then bought this tool. It took about 10 minutes to assemble and attach it to the hub and then another minute to push the axle out with ease. My only regret is not buying this hydraulic puller sooner. I will be getting a lot of use out of this on other projects. I like how the puller arms can be reversed for two different jaw sizes. As others have noted, the case is a little cheap, but it does the job, and the quality of the hydraulic puller seems to be very good.

Had a stuck brake drum on my tractor that would not come off any other way. I tried a three jaw plier, PB Blaster, impact hammer, and heat. Nothing worked. Then, I read the reviews on this product and thought I would give it a try. Worked great. The seller was responsive to my questions, and followed through to make sure that I was okay with the product. Big help.

Lasted like 10 pulls then started leaking oils