BANG4BUCK High Performance HVLP Gravity Feed Spray Gun with 1.4mm 1.7mm 2.5mm Fluid Tips, 1000cc Aluminum Cup for Auto Paint, Primer, Clear/Top Coat & Touch-Up

Cheap gun but it works fine. No DV-1 here but a good primer gun. Sprayed out some thick stuff with only the 1.7 tip. The 2.5 tip will spray out the body man in a can thick stuff. (Slick sand). Came with lots of extras but the downside is you have to use the wrench provided to change the tips.

This gun worked flawlessly. So much better than other cheap brands We used this for two part paint for a large sailboat.

I received this yesterday and started painting with it within the hour. The first comment i need to make is about the lid, THE LID ON MY UNIT IS TIGHT AND DOES NOT FALL OFF. Maybe they saw the comments and fixed the issue others have had. i was using the 2.5mm nozzle and found there were no leaks at all. I tested with water first and then switched to a heavy Behr Premium Latex paint and primer in 1. The first batch of paint i used floetrol and water to thin it out and it sprayed just fine. after i drained that first container i started putting paint with no water or floetrol and the gun still worked fine. I have a 60 gallon air tank with a 3.5 hp pump, it has two air/water seperator filters in line and i set my line regulator to 55 PSI which it holds even under load. I did not use the supplied regulator at all since i have a much better regulator on my drop line. I use high flow quick connects too so no restriction at the connection point. I could spray non stop without running out of air and the gun never stopped longer than refilling for 3 hours. Cleaning was really easy, i just ran water through the sprayer and rubbed all the splatter off the outside with copious amounts of water. i also disassembled the gun and brushed out the inside as well. Just remember when assembling the gun, you dont need to torque it down hard, you will have to dissasemble between jobs anyway so just snug it down and move on. Dont make more work for yourself. The only reason its not 5 stars is the fit and finish does feel cheap with flexing on the handles and sharp bits on the machined metal.

this gun is great buy it and a new cup for the top has all the tips you need at a bargain

Shot these cabinets with the 1.7 tip and Sherwin Williams Gallery and they turned out great . Some pointers. No need to thin the gallery paint, but it will have an orange peel appearance when shot, but then will lay flat. Before you fill the cup with paint, set your pressure on the gun at 25 to 30 psi with the trigger pulled and the air flowing. Do not use the included strainer at the bottom of the cup, as latex paint will not flow through it properly. Just use Harbor Freight 60-70 mesh conical strainers when filling the cup. I wish that I would've known these details before I started.

9/25/25 Update. Seller read this review and contacted me to fix the situation. They bent over backwards to fix things for me, and totally deserve credit for that. It’s rare to have a seller stand behind their product like that and be willing to go so far to fix a situation. So I am changing my review to five stars as if you do get something wrong with your kit, they will fix the situation. 9/20/25 I bought this specifically for the 2.5mm nozzle. The 1.4 and 1.7 nozzles that come with it probably work fine, they close and thread and seal and assemble as they are supposed to. But the 2.5mm nozzle and pushrod are wrong size for the device. You can see in my picture the 1.4 and 1.7 pushrods are on the right and correct sizes. The 2.5 is on the left and is far larger. The excessive length will not allow the knob on the back of the device which holds the reset spring assembly, to close and thread, rendering the unit inoperable with the 2.5 installed. You can see in picture 2 with the 2.5mm pushrod installed, it sticks too far out the back and the rear thread-on part that is supposed to cover the rod and capture the reset spring can’t actually seat on the unit or catch threads. In picture three you can see the rear part placed over the pushrod, and you can see where the threads are suppose and catch and thread together, screwing in. But the pushrod is too long. It can’t close and thread together. The rear part is what holds the reset spring in so when you squeeze the handle and release, it resets the handle turning off the sprayer. Meaning, the failure to thread together prevents the unit from operating m. It’s useless for me because I only needed the 2.5mm size. And it’s the one size that doesn’t work. The seller included a “contact me” card, but following the instructions, it is apparently outdated, and doesn’t work. I tried to find another way to talk to the seller and can’t. So I’m leaving this review.

Spray nozel is on so tight that it bends the wrench trying to unscrew it right out of the box. New never used. This is spray gun #2. Both have the identical problem. Returning it and ordering spray gun #3

I mainly bought this to use as a cheap primer gun, it’s worked alright, but you do have to really fine tune it to spray how you want. I wouldn’t buy it to spray color or clear though, strictly primer. Other then that, I’ve had no issues with it.

I would recommend this gun to anyone have painted a few trucks with it and does a professional job everytime, don't get reducer on the regulator lense it will eat it is my only complaint

Worked perfectly. I used this gun to shoot undercoating, easy setup. Did exactly what I needed it to do, didn’t even bother to clean it I just tossed it out

El producto llegó en buen estado, pero la llave no es como la que se muestra en la imagen.

I am an amateur and first time using the top canister like spray gun. Worked great. I sprayed a flat green. Easier to use. Recommend buying the stand to hold it up right. That is a must.

malo. solo es un vaso de aluminio. nada que ver con lo que indica la publicacion