DEWALT DWA2600IR Impact Ready Conduit Reamer

Works great with a DeWalt drill.

I like this a lot. This is so neat. The blade is spring loaded as retracted. When you use it press into the tubing and the cutter blade extends and removes the burrs. Just a few revolutions and the emt tube is smooth as can be. This makes a great gift. New replacement blades are available on Amazon.

Muy bueno

The magnet that is supposed to hold the tips to the reamer is not very strong and the tips easily fall out.

This product reams so sell that I would say it does a better job that the factory end on EMT. One piece of advice I have though is to buy a couple of extra blades and throw them in your tools because they are harder to find and its inevitable that you will break them. I've gone through as much as 1 reamer blade once a month on a job with a lot of pipe work but its worth it. It does an incredible job, saves a lot of time, and most importantly it saves wear and tear on my wrist.

I love this reamer. Once you learn how to properly use this tool it will ream conduit with a smooth, clean finish in 3 seconds. I use this on a Milwaukee drill set to second speed on the drill setting without the clutch. I place the tool completely in the EMT only applying slight pressure but not enough to engage to blades. Spin the drill to full speed then push down so the blades come out and start to ream the pipe but do not push the reamer down so hard or the blades will catch in the pipe.

Great for Impacts but also can be used on drills. Short burst of trigger needed. The blade is hidden until pressed on end of conduit. No catching on or making holes in pockets when not in use. Comes with square tip but can easily be replaced with Phillips head. Best when reaming multiple conduit at the same time like when lining up conduit ends. Time and wrist saver.

I am going to give this a middle of the road review. I found complications with the product that are specific to my tool/work set up. So your mileage may vary here. I use this tool in commercial electrical work with an M18 FULE v2 Impact driver on #2 power setting (1500 rpm), and a metal cutting saw that produces little to no burrs but can leave one large tassel on 3/4 EMT periodically. I can say that I have broken two of these my own and a co-worker's (sorry bud), with my impact, both of them the tools blade broke off. His version was a non impact rated and bought at home depot, while mine was purchased here. That being said he and others that use lower power M12 or Dewalt tools have NEVER had an issue. I believe that the high torque and impacts of new hi power tools may be an issue, beyond this I have been pleased with the design, price and utility of the the tool.Pro: What I love about this tool is that it's blade retracts inside the sheath making it less likely to snag on tool bags/ gloves and providing an extra measure of safety and convenience.Con: Tool may not be strong enough to handle M18 2 gen tools and Dewalt 24v on high settings.I can and do recommend this tool to others but they are using lower power tools than I. I am replacing this and using a lower setting or smaller battery pack from now on.

Works great. I was hesitant at first cause some reviews said it broke easily. It's not the case, I never ran my impact full blast, I had it one setting 2 and ran it on that and it's been working perfect

4th conduit reamer over 5 years in the trade.1/4 drive is thicker then the klien reamer.Allows you to save it if your impact takes a fall from the ladder, Dewalt reamer survives better.The spring loaded sheath also is handy for taking down sharp teeth after a rough cut.Only one I tell apprentices to get.

Fonctionne très bien et est impressionnant mais attention à ne pas utiliser sur du cuivre, chauffe beaucoup et la vis de soutien à simplement sauter, je la cherche toujours car ma lame est encore bonne

Great tool

Works great but the Robbie head gets stuck in the screws. I wish I locked in better. Be careful using an impact gun it fired swarf everwhere