Kreg R3 Jr. Pocket-Hole Jig System - Portable Kreg Pocket-Hole Jig - Easy Clamping & Adjusting - Includes Positioning Sliders - For Materials 1/2" to 1 1/2" Thick

I have been using Kreg jigs for many years now, and have this item's predecessor. While I could not live without it, a few things always bugged me - and they all got fixed in this version. It was enough that purchasing it was a no-brainer. The biggest improvement is the built-in offset lip with markings for all typical lumber sizes. In the old one I had to actually screw the lip that is used to align to the edge of the board on using two screws - and if I was using 2x material, add a spacer using different size screws - and if I was using anything else I had to measure and line it up manually. Good if I was doing a lot of boards, but a real pain for one or two and worse if I was switching back and forth! With this new model, just press in on the tab and slide the gray guide forward until it snaps into place at the mark for the size board I am using. Second, with the lip in place, the Kreg clamp I was using was trapped in the jig and if I wanted to use it for something else, or just put it away, I had to unscrew the lip. Done away with in the new model, there is a spot sized for the clamp that is proud of the jig. Very easy. Third, this comes in a nice little case that holds everything but the clamp. My other was part of a set of Kreg jigs so when I wanted to throw it into the toolbag to go to a work site, I had to put all the parts in, and some would eventually go missing. Now I can put the case into the toolbag, very handy. Fourth, the jig from the old set that showed where to set the drill stop required me to lift the drill out of it in order to get the stop on, and of course it would sometimes slip when I tightened it so I have to recheck and sometimes adjust. Honestly it was such a pain that I got an extra bit and stop just so I could leave one set for 3/4" material and one for 2x material. In the new model the jig is part of the case AND holds the bit at each end, leaving space for the stop so I can tighten it without moving the bit. Clearly Kreg is listening to their customers and making very handy and sensible improvements while maintaining their high quality. Like I said, buying this one even though the old one still works was a no-brainer. Now I'll just set up the old one for 2x material and leave it.

I've used the Kreg R3 Pocket Hole Jig on many woodworking projects over the years, and I can say that it is an excellent tool for anyone looking to get started with pocket hole joinery. Pocket holes are my favorite method of joinery because they are very strong and easy to hide, and the Kreg R3 makes it easy to create professional-looking joints. One of the best things about this jig is its cost-effectiveness. It is an affordable option for anyone who wants to start building furniture or other woodworking projects using pocket holes. The jig is also very easy to use, even for beginners, and comes with clear instructions that make setup and use a breeze. However, one downside is that the square bit can deform if driven with too much power. This can be a problem if you're using a drill that doesn't have adjustable torque settings. However, with a little bit of practice, it's easy to get a feel for the right amount of pressure to apply. Nevertheless, I've found that the drill bit that comes with the jig stays very sharp over time, which is a huge plus. It's also easy to find replacement bits online or at most hardware stores, so you don't have to worry about running out of bits when you need them most. Overall, I highly recommend the Kreg R3 to anyone who wants to start using pocket hole joinery in their woodworking projects. Its cost-effectiveness, ease of use, and ability to create strong and professional-looking joints make it an excellent investment for any DIY enthusiast or professional woodworker.

I had never done a pocket hole before. Doing DIY carpentry. a lot of it. This has really made the difference in crappy quality and amazing looking work. I'm building a walk in closet in this reclamation project of a home I just bought. I've built floor to ceiling closet storage bays, 8 total at about 3ft wide, these corner joints are seamless and as long as your cuts are straight everything is solid and looks professionally done. Then, i built two window storage seats, again a huge help. Now, I'm building the storage island, which is basically two dressers back to back with a shared lid and side coverings. Project after project I'm doing pocket holes. it's so much easier than making biscuit cuts or any other form of corner attachment. What I am liking so far: Compact size, comes with a solid case, and I didn't see this in the listing, but came with a small sample back of screws. Other tools you'd need: I do recommend the Kreg Clamp this is designed to work with the tool and makes the effort of clamping and screwing much easier. Keep it really snug, if you have a light grip you can sometimes have the jig slide around on the board. https://www.amazon.com/Kreg-KHC-PREMIUM-Face-Clamp/dp/B001DC9UR8/ref=pd_bxgy_469_img_2?ie=UTF8&psc=1&refRID=K8D41RETZYYY99JMZCC9 Final thoughts: It is a little time consuming to move this back and forth all over boards to do multiple holes, but at the same time that makes it versatile. There are other rigs mad by Kreg that would be a little faster. Speed aside, it works well and i've probably drilled about 300 holes with this in the past month.

Muy buen producto fácil de usa

useful for DIY projects.

ポケットホール用の治具、中華製もいろいろありますが本家本元ということで購入。 プラスチック製ですが丈夫です。最初ドリルを通すときにプラ部分が削れますがこれで公差を小さくできるようです。 グリップ付きなどいろいろバリエーションがありますが、いちいちクランプで止めるのは面倒ですがコンパクトでDIYでは十分です。ケースも付いています。 専用のビスは高価なのでコーススレッドを使ってます。半ネジではないビスを使う際には4mmのドリルで下穴を開けてます。

Excelente gabarito. Usei várias vezes, em mdf e madeira maciça (dura e macia) e o resultado é sempre bom.

This is my first pocket hole jig so I may not give the best review with no reference. But for me this is great because I just follow the instruction and then everything was like falling into place. I love the experience in using this jig