SRUNP Car Phone Mount with Three-Point Support for Car Dashboard, 360 Degree Rotatable Washable Cell Phone Holder for Car Compatible Smartphones and GPS Devices

I use this in my husband‘s car for car trips because we use my phone as the map. It works great on his texture dash. And then when we’re home from the trip, it comes right back off. I put the paper cover over the back. And next time I peel the paper off, stick it right back on the dash. If it stops being sticky, you need to wash it with a little soap and water. Let it dry and feel free to use it again. Just save the cover that comes on it so you can protect it when you’re not using it.

Simple to mount, sturdy, it rotates, it's effective... and not expensive!

I like that it’s small and not intrusive like the cup holder mounts. It sits nicely on my dashboard and hasn’t moved even though it doesn’t stick permanently. I haven’t tried to wash and reuse yet.

I had another holder that had a catastrophic adhesion displacement while driving. Since I had an existing puck from an old timey GPS unit, I purchased this holder and slapped it on the puck and that thing is stuck there for the rest of my car's life. The holder turns so you can adjust it the way you want it, and the most important thing: it accommodates my Loopy phone case (loop in the back). You plop your phone into it (the holders won't even come into contact with the side buttons or press against the screen) and holds it securely. Just pick it up and go, no latches, no nothing, it just holds your phone and will work either landscape or portrait (I do landscape, haven't tried portrait). Love this holder! Simple, basic, does the job.

I have a Subaru Crosstrek which has some challenges with the dash area to mount your phone. I don't like using the vent mounts as previously having one, it busted my vent. I was excited to get this as it is a minimal looking mount that doesn't cause an obstruction to my view when my phone is in it or when it isn't. It's not big and bulky and the swivel is a nice advantage. However, when I turn a great majority of the time the phone falls out. I do want to mention this is when my phone is in it vertically as that is how I need it when driving. Horizontal may not have as much issue. But, instead I have to usually pull over and get my phone and put it back or just not have my phone in the mount which defeats its purpose.

Good quality.

I've bought and used many types of cellphone holders over the years but they all fell short of convenience or holding power. The windshield suction types sucked, but in a bad way including falling off and not to mention blocking the field of view. The magnet type was great, until I realized they interfere with wireless charging. Then there were the kind that attaches to a vent until one of the vents broke over time (a pain in the neck to fix). Finally they came up with the cup holder cellphone holder. It wasn't cheap. It worked, but you had to keep adjusting and futzing with it. Then after some time I realized that I needed that cup holder... to hold cups! Especially on long rides with my wife next to me, who got tired of holding her own drink in hand. I found this cellphone holder on Amazon and I must say it makes the most sense for me. It's simple stupid, easy to install, tightly holds my phone in place. Does not impede my view, rotates left or right and it doesn't even fall out when my HEMI kicks in and burns rubber or if I have to lock up the brakes! Most importantly though is my peace of mind of not having to listen to the wife complain and threaten about putting her drink somewhere. I highly recommend this product. If I could, I'd give it TEN STARS!

This phone holder is amazing. The only downfall it has is that it doesn't stick in place, so if you make a sharp corner, your phone and phone holder fall down. There is a way to wedge the phone and holder against your windshield to stop this from happening, though, which makes this my favorite phone holder that I've ever used this far

Good quality and easy to use

Not sure if I should stick this on my dash as the back is not as illustrated on the website. Website shows a small center for the adherence spot, mine came with the complete back as a sticky surface. I want this to be removable. Please let me know if it is. Thanks in advance, Art.