LeMotechWaterproof Dustproof IP65 ABS Plastic Junction Box Universal Electric Project Enclosure Pale Gray 9.0 x 5.9 x 3.4 inch (230 x 150 x 87 mm)

I got this so I could have a neat installation of an outside security camera. I cut a hole in the back for the for the power supply line of the camera and another in the cover with 4 holes to mount the camera. I drilled a hole through the wall for the camera's power supply for the power supply line of the camera, mounted the box over the hole with the expanding wall anchors. I mounted the camera to the cover with small bolts that came with it and plugged the male end of the power cable into the female end snaked through the wall hole. I used silicone caulk between the camera and behind the box and the wall. The excess cable was coiled in the box. The cover fit fine over the coiled wires. The assembled box was very sturdy with the included cover screws. All in all a very easy, very neat, water tight installation.

Performance was good. Very sturdy. seal was good.

These are great low-cost enclosures. They're easy to machine without breaking if you do it right!. The screws for the cover are outside the seal and therefore don't come into play for water resistance. The lid has a specific orientation. Make sure the orientation is correct before screwing it down.There is a lack of detailed specifications and no detailed drawing. The screws for the cover are metric, M4x25 (~4mm diameter x 25 mm in length). There is no material specifications for the screw. If you plan on using this outdoor or in an area where moisture is present, I would suggest changing out the included screws for stainless screws. I was short one screw for the final assembly. I ordered another enclosure because that was cheaper than trying to buy a replacement screw. No subpanel is included with this size enclosure but one could be easily fabricated.

There are bosses inside the box for a mounting plate, but there are no dimensions and no mounting plate. Otherwise, very good quality plastic box.

Arrived quickly. Had a problem, one lid screw missing. Robin from Customer Service contacted us immediately and made everything right. Have the box all set up for an RV rooftop application. Completely satisfied. Outstanding Customer Service!UPDATE: We were asked to write an additional review, so here it is. We liked the box design. The four lid screws were outside of the interior area of the box, so now water infiltration is possible via the lid screws. Additionally the lid includes a mechanical waterbarrier and an o-ring gasket. We are confident that this box is weatherproof. The box plastic is very hard, but it is a bit brittle. We were able to drill four holes through the sides of the box with an ordinary hole saw without issues. We mounted a back plane inside the box using the molded in standoff screw holes. While carefully installing three screws into the standoffs, one standoff cracked. The only other problem we had was the box arrived with one of the four lid screws missing. We went to the local hardware store and purchased 4 new stainless steel screws. The screw that was missing had damaged threads in the insert. Fortunately the hard stainless steel machine screw was able to tap through the thread damage and now works fine. We have the box installed on the roof of our live in RV and it is working fine. We are completely satisfied with the box. As I mentioned in the first review, this company contacted us right away upon seeing our review that we had some problems. They have outstanding customer service that is unmatched by any recent experience we have had with any other company. We would definitely buy from this company again. Thank you LeMotech!

Nice simple product that works. I used this box on my vinyl outdoor gate to house the Ring Alarm Contact Sensor (2nd Gen). I left the magnet side exposed to the weather. I'll update the review after winter to see if any problems show up. So far so good.8-19-2023.

Good quality. Easy to drill.

Box comes with a length of rubber seal that's too short to make it around the box. It leaves a good inch where water can come through easily. Otherwise it's a nice product.

Great for making low power End Fed Half Wave antenna UN-UN transformer.Perfect size for single FT140-43 with associated connectors.Boxes are well made and should take some abuse in the field.Bought the 3.3 x 2.3 x 1.3 inch (83 x 58 x 33 mm) size.

良い。

I wanted a clean solution to house an outboard high pass filter for my power amplifier.This was a cost effective and well made casing for it.

期待通り、の製品でした。アマチュア無線のANT切り替えディプレクサ－を入れてますが、雨水の侵入は、有りません、かつ点検時開閉の蓋は、大変重宝します。

Works as advertised.