Bluetooth Power Amplifier Board with Subwoofer 2.1 Channel 50W x 2+100W DC 12V-24V Audio Power Amplifier Module for DIY Bluetooth Audio and Store Home Theater with Treble and Bass Control

Is perfect

So far so good

Did not work properly i dont like it the item was damaged

Before continuing, ignore the way it's put together in the photos for the listing, it's been assembled upside down (see the DC power going into the port labelled Aux-In, for example). The provided instructions are a poorly photocopied single sheet of A4, that don't provide any details about Bluetooth pairing and the likes, but that's fine - I only want to use a wired connection because I don't want any latency (it's for synthesisers). Fortunately it's not a hard thing to build - if you've got any sense at all you'll manage. It even comes with a terrible screwdriver to help you along the way! The entire case, which is just a top and bottom with the panel for the knobs already in place, is made from PCB material (the same as the PCB - crazy, I know!). Given the sides and back are open to the elements I guess its main purpose is to prevent fingers getting close to the heatsink. It's all quite 1980s futuristic, being black with silver for the labels! The provided knobs are also silver in colour, and just a bit too shiny for me so I'll swap them out later. All the hardware is provided, but there are no spare screws or anything which means that, if you drop one of the tiny screws, you might be in trouble. I dropped one... but I'd hoovered the workshop floor a minute beforehand so I found it very quickly. That's all my complaints done. It's actually a very capable little amplifier and can bring life back to speakers that you've had sat on the side for ages because they're too good to get rid of. For me it's using the speakers from an extremely old iPod dock - it hasn't been used since 30-pin connectors were abandoned - and it does a fine job of it. The subwoofer didn't make it but the main speakers sound good. I've not tried the Bluetooth, as explained, and I've only run it on a 12V supply because that's what I had to hand. It's a standard 5.5x2.1mm barrel jack, centre positive, and you've almost definitely got something that will power it in the house already. With better instructions, knobs and enough screws to be able to drop one without panic, it would be a five star review. As it stands, it's a good part to modify lightly for projects.

Installed this tiny powerhouse in my Polaris side by side EV UTV using some 3.5 inch coax midwoof tweeters (Orion Cobalt CB35) in the dash above the cup holders whci was the biggest speakers I could fit cleanly with custom 3D printed carbon fiber infused adapter plates. I also installed Rockville VS8K54 8" K5 800W Car Subwoofer under the driver seat (the UTV had been converted to Lithium so that space was empty now, 4 12 volt batteries on that side gone). This combination works awesomely as the adjustments to the sub frequency cross over and volume allows precision matching and provides plenty of power. I am 100% happy with this amazing little amp/bluetooth setup and would highly recommend it for someone trying to put together a decently loud, full range sound that thumps and plays clean on a wide range of music, from deep bass techno through complex melodic vocal instrumental.

I was surprisingly happy with this little guy! AWESOME bluetooth connection, Seriously ..minimal latency, no buzzing or humming or sound interference, quickly connects & provides a strong clean connection that I've tested at 35ft away outside of building while device is inside. I have not yet measure the true watts rms output yet, mainly because it honestly sounds accurate with proper power supply & wired at 4ohm for speaker/sub. Don't bother using if using a 12vdc power supply as it will distort sound, generate more heat, and stress all equipment. For clear audio with good mids crisp high and punchy lows, use 19vdc 3amp to 24vdv 6amp. very minimal heat generating from device with this power supply range, even with hours of high volume bass use. If a 2 speakers 1 sub (in this range of watts) head unit is what you're looking for, I Totally recommend this lil guy

For diy it works well , it has good power and not to noisy at low volume could use a better shell to much exposed parts

A very capable amp for $16. I regularly test car audio speakers and used to have complex amplifier/power supply/wiring set up just to do so but with this simple thing, it's just plug and play and the output is stronger than a lot of tiny car audio amps costing 3 or 4 times the price. Very nice and convenient. Not sure how well the circuit protection works though. I purchased one before and accidently crossed the + and - leads on the subwoofer channel for just a split second and the amp started smoking and stopped working. Didn't return because it was my fault.

Great mini amp for my record player. The sub feature is really good. The size is great for a small space. Bluetooth was easy to connect. Really good purchase.