RMR-86 Instant Mold and Mildew Stain Remover Spray - Scrub Free Formula, 30 Fl Oz

Ok, seriously, if you’re brave AND a home owner, BUY THIS.This is the literally the BEST product for mold or mildew i have ever used.YES, it may need to be evaluated by the Chernobyl Nuclear Assessment Team down the road, but PLEASE let me explain and leave some application pointers#1) If you're not using PPE + a respirator, make SURE you only plan to work on small patches at a time, and in a well ventilated area you can get in and out of to fresh air quickly. I cannot stress this enough. This stuff is STRONG. As in...BLEACH x about 5. You can Taste It.Do NOT BREATH IT! If you can, hold your breath, hold the bottle at a safe distance, spray the area quickly, then runaway!“Spray. Then Runaway.”#spraythenrunaway#2) Get a CLEAN towel and place it under the door crack of the room you run out of after spraying. use it, ALWAYS! Clean towel is your buddy here.#3) After 15 minutes, Hold your breath and check out your progress carefully. It dries VERY quickly and the smell/fumes drop to a good 1/2 of what they are during initial application. Again, wait AT LEAST 15 minutes before checking. More mold? Spray a bit more in the areas that need it, ...runaway #spraythenrunaway, ....wait 15 more mins and check again....same process as above.#4 Repeat protocol until about 15-25% of mold or mildew remains.#5 WAIT 2-5 HOURS then check again. At this point, the mold should be almost 100% gone.#6 IF more application needed, repeat process again as many times as needed, ....then proceed to fortune and glory.My Actual Spray Process I used on our Bathroom Window Casing:1. Remove Blinds.2. Cut large piece of cardboard out to use as a mask for window vinyl, steel or fibrex behind the wood casing.3. Grab paper towels, about 10 squares and fold them into little wads that can be stuffed at the bottom of the window sill's left and right sides to catch the runoff from the vertical side casings.4. Grab a small ziplock bag to store the used paper towels in and keep them sealed up and the fumes contained. You can just leave that in the sink.5. Get a fan and set to low about 3 feet from the open window and blowing toward it.6. Grab your cardboard and your RMR 86, take a deep breath, hold it....hit the left side wood casing, using the cardboard as a mask for the window behind the casing, hit the right side, same process. Do NOT try and do the top casing, or spray will potentially come back down on you and get on your skin. Don't overspray. Just hit them quickly enough to cover each side. About 15-20 seconds total should be fine. Stuff paper towel squares in the lower right and left window frame, runaway! (for me, I closed the door behind me and stuffed a paper towel under it. Worked like a charm as the smell never got into the rest of the house.15 minutes later, I cautiously walked back in each time, smelling carefully from a distance and as I approached, as I said, the fumes and volatility drops a LOT after the first 15 minutes but is still STRONG!I removed the paper towels used to capture the runoff in the lower left and right sills, sealed them in the baggie, dropped it back in the sink. Then went outside the room to fresh air, took another deep breath and repeated step 6.Our casing was BAD, so I had to hit it about 4x over an hour.For me, and because I was doing such a small area with plenty of ventilation, I did not go full PPE or respirator. I used long dish gloves, goggles and held my breath each application, keeping the airflow via a fan pushing air OUT the wide open window and as to move any overspray or fumes outside asap.The first application, not a lot of difference. Second, BIG difference. By application 4, 85% of the mold and mildew were gone and we were looking at CLEAN wood. Next morning, I checked and the mold was 100% GONE...so this stuff KEEPS working long after that 15 minute mark. I'd say it likely keeps working up to 24 hours after application so expect to see additional progress on the affected area up to a day later.For the TOP casing, I waited until the sides were treated as explained above. Then 2 days later, I used the same ventilation setup as before. This time, I grabbed a paint brush, poured a tiny bit of rmr 86 into a plastic cup, and lightly painted it onto the top casing, still wearing gloves and goggles. It took more applications...i believe 5 or 6, but was a lot less stressful as I was using so little of the stuff and the fumes, although still bad, were no where near what spraying did. Each application, I'd let sit 15-20 mins, and I kept the paint brush and tiny bit of RMR solution in a cup in the sink so I could just grab and go each new session or dump out with running water. This worked well on the top casing as it was no where NEAR as caked as the left and right sides were, but something tells me, spraying/aerating this stuff out of the bottle must increase effectiveness, as it IS a corrosive and reacts with O2.I'd say if you're doing ANY job larger than what I described here, go Full PPE with Respirator and make SURE the room you are working out of is well ventilated and siphoned OFF from the rest of the house.If you're just squirting a few corners of your bathroom...1-2 squirts, 1 area at a time, then gloves, eye protection and lotsa of ventilation should be fine. Higher up areas, I'd recommend the paintbrush trick. And I'd personally NEVER try and spray multiple areas in the same room...I'd do 1 at a time and leave. Even a few squirts in a few areas adds up fast, and you don't want to create a potential "fume trap" by which you get a breath of lingering spray and burn your lungs/throat, etc. Not worth it!

I used this spray on mold in my bathroom caused by lack of ventilation, and it worked exactly as promised. The stains disappeared almost instantly with no scrubbing required. The application was simple, and the results were noticeable right away. All I had to do was spray the problem areas and let it sit and do its job.For safety purposes, I opened my bathroom window first, grabbed some goggles and gloves, wrapped my hair, and then I sprayed. Since I was spraying the bathroom ceiling, I wanted to protect myself as much as possible. Also, the smell is strong, maybe as strong as a bleach smell, but make sure to open a window first.It’s rare to find a product that works this well, but this one truly does.

I had some mold forming in our crawl space and decided to try the RMR first before calling in a professional company. I called RMR and they walked me through exactly what needs to be done and to make sure I'm using the correct PPE for the job. I started with the RMR-86 spraying all the areas then following up with the RMR-141 a few minutes later. I let the products do their magic and returned later in the day once all the fumes have settled and found all the spots to be mold free now. It's been almost 3 weeks now since I applied it and all the areas are still nice and clean.The product is very easy to use but make sure you're using full PPE (Tyvek suite, gloves, goggles and respirator) as this stuff is very strong. Since then I've used these products to spot treat a few mold spots in our shower and had the same great results. Being a smaller area to treat I just ran the bath exhaust fan and opened the window and closed the door. These are great products when used together and RMR has great customer service willing to answer your questions about their products.

Leaked in package but very powerful, very potent, and not a sham.This stuff works. Definitely "Bleach on steroids". I strongly, strongly recommend you buy a respirator (you know, like the gas mask with the filters) as N95 was not sufficient to block out fumes. I also suggest a hazmat suit or coverall, because skin contact can cause chemical burns. If you're a risk taker and are without a full-face respirator, you might want to use swimming goggles to avoid eye contact.Minus a star because the package was leaking from the bottle a bit, even though it is sealed. However, the product is contained within its own box which reduces the amount of damage to other products you have in your order (order separately if this is a problem). You use the nozzle straw to pierce the tamper protection.

WTF - What The Fabulous...I did not have high hopes for this stuff, even after watching videos and looking at pics. Well, I can 100% tell you this stuff works like a miracle. Not only does it destroy mold, it destroys stains and mouse tracks (if you live in the country, you know what I'm talking about). It is crazy what this stuff can do. I'm not done with what I need to do and guess I should start taking before and after pics to post.One thing I must point out - this stuff is toxic. I literally wore TWO dust masks over my nose and mouth as I had to spay this chemical in a small tight space. The smell did get thru and actually stuck in my nose until I took a shower (which I did immediately after spraying it) - BUT ALSO it started burning my eyes (I wear glasses, but think I may need to wear swimming goggles next time).No doubt - this stuff does what it advertises!

I’d give this 10 stars if I could!! You literally just spray and the stain goes away! I used it on mildew spots on my bathroom walls, and it worked like freaking magic. I’m so mad I scrubbed the walls months ago and tried getting it off instead of just buying this. It does have a STRONG smell, almost like bleach but the contact high is worth the walls not looking nasty lol