Broan 641 Wall Cap for 6" Round Duct for Range Hoods and Bath Ventilation Fans

My unit came in perfect condition and well packed. It's a simple design but works well. My original vent cover was a cheap plastic louver that was screwed to the wall using masonry screws. Because of that I had to chisel around the exhaust pipe to fit this around the pipe. I had to use a mallet to get the cap seated and it stood up to the pounding with out any noticable damage. After I got it snugged up I was able to screw it flat to wall and seal the edges with silicone caulk. The end product works well, looks good and prevents back drafts. It was a little difficult to install because I was replacing a different style of cap. I suspect if you already have something similar this would be a quick job.

Very happy with this wall cap. We installed a vent pipe as part of our kitchen remodel. This part of the installation was very easy. Despite what other reviews said in the past, I found no construction or quality issues with this item. The spring is tight but the damper opens easily. The screen at the end is removable, and although it will not prevent insects from taking residence, it should provide an adequate deterrent to other kinds of pests. My only slight caveat is that I would have liked to have had some additional instructions for installation. We put this over our vinyl siding rather than under as the outer flange is the same size as the lap, and the hole position was non-negotiable due to structural obstacles interior to the wall. We would have had the bottom edge sticking out if we had put it under the siding, so we put it on top. I screwed 2 screws in it and caulked the heck out of the outer edge. I *think* we should be fine--- but it would have been nice to see some additional guidelines/suggestions in the box.

The cap arrived in excellent shape. The spring loaded damper closes flat against the gasket. No modifications required. The bird (bug) screen is 1/4" hardware cloth and should keep out most critters and it was installed securely and should not fall out. The collar is short, about 1.25", but I knew I would have to be attached it to a piece of duct to extend it through the wall. The collar fit over the crimped end of the duct with some persuasion, typical of most ductwork. The cap material is fairly light gage but should hold up fine without abuse.

This unit replace my plastic piece of x. The old one broke and we almost had bird problems in our duct. I had it professionally installed, so I cannot speak to installation. The screen that covers the opening and the spring loaded flap are the main reason I purchased this wall cap. It is much quieter than my old plastic one. It works well, but as others have said, the rubber seals don't allow the flap to fully close. It is such a small gap that I cannot complain too much. I just spray it with bug spray and bee spray to help keep out any unwanted tiny creatures.

We have a cooking stove exhaust vent blower that has a top speed of 750 cfm. We were going for a vent cover that could handle the exhaust and keep out unwanted pests. This was a very satisfactory solution. Easy to install. Well made, sturdy, a thicker grade aluminum, with a screen to keep critters out and a gravity flap that's closed when not in use.

A different range hood vent was previously purchased, but the rear connector was too long. This model has a a very small female connector and only required the connector sheet metal to be crimped. The hood is well constructed and looks nice.

relatively easy to install except I was 30 feet up a ladder on the side of an attic wall . It has a projection of about an inch of the 6 inch pipe that goes into the wall . Pretty heavy gauge aluminum with a spring loaded damper and a removable piece of hardware screen to deter the critters from trying to get in . God Broan quality

I have used this before, and am aware of the shortcomings, but I wanted a matching vent for a new bathroom fan installation. As others have noted, the flap doesn't fit well. Whenever you see a product with a weatherstrip, but the manufacturer didn't take care that the parts actually touch the weatherstrip, it kind of makes you scratch your head and ask, "what the heck were they thinking?" As it happens, a little massaging (bending) of the door made the fit better. Fortunately, it doesn't have to be perfect. The bird screen snaps into place and, isn't well retained. A couple of well placed sheet metal screws retain it a lot better. You can use the same sheet metal screws you use to connect the duct sections. A bigger problem is that the collar where the duct attaches is too short. The Zephyr AK00042 has a much better collar length. With this one, if the wall is too thick, attach a 6"-12" long piece of duct to the cap with duct screws before putting cap in place from outside. You shouldn't use screws if you are using this for dryer vent (screws protruding into the duct collect lint and eventually clog the duct), so if you're using this for dryer vent and the collar is too short in your application, use a different cap like the Zephyr. It's annoying that you have to worry about all this. The positives are that this cap is aluminum, not plastic that may deteriorate in outdoor application, and it's made in the USA. I cleaned, primed and painted mine (Rustoleum primer and paint) before installing to avoid a big silver-looking eyesore.